Go Back   IceInSpace > Equipment > Equipment Discussions

Reply
 
Thread Tools Rate Thread
  #1  
Old 03-10-2021, 11:16 PM
raf.serrano (Raf)
Registered User

raf.serrano is offline
 
Join Date: May 2020
Location: Melbourne
Posts: 27
Celestron Mount Rebuild

Hi all, I just recently got a used Celestron CGEM mount, my first full size mount as I have been using the AZ Gti. The mount has a little bit of wiggle on the dovetail clamp and counterweight shaft so thinking of opening it up to see if its something I can fix and maybe regrease the bearings too.

Problem is I cant see any videos of a Celestron CGEM rebuild, anyone have recommendations? Would there be a similar mount rebuild instructions I can refer to disadsemble the mount? Also what is a good way to remove oil and stuck grease?

Any advice and words of wisdom is greatly appreciated, clear skies
Reply With Quote
  #2  
Old 04-10-2021, 07:52 PM
Eldest_Sibling's Avatar
Eldest_Sibling (Alan)
Registered User

Eldest_Sibling is offline
 
Join Date: May 2017
Location: Mid-South, U.S.
Posts: 136
I remove Synta's factory glue-grease with charcoal-lighter fluid, used for grilling food outdoors. It's a light grade of kerosene, and cuts right through the old grease...

Click image for larger version

Name:	RA de-greasing.jpg
Views:	338
Size:	46.2 KB
ID:	281579

The CGEM is considered too complicated to work on by the average user, which is probably why you're having trouble finding renovation material. Of course, I would work on one regardless, so welcome to the DIY club.

There are folks working on theirs on YouTube...

https://www.youtube.com/results?sear...Celestron+CGEM
Reply With Quote
  #3  
Old 04-10-2021, 08:08 PM
multiweb's Avatar
multiweb (Marc)
ze frogginator

multiweb is offline
 
Join Date: Oct 2007
Location: Sydney
Posts: 22,071
Quote:
Originally Posted by raf.serrano View Post
Hi all, I just recently got a used Celestron CGEM mount, my first full size mount as I have been using the AZ Gti. The mount has a little bit of wiggle on the dovetail clamp and counterweight shaft so thinking of opening it up to see if its something I can fix and maybe regrease the bearings too.

Problem is I cant see any videos of a Celestron CGEM rebuild, anyone have recommendations? Would there be a similar mount rebuild instructions I can refer to disadsemble the mount? Also what is a good way to remove oil and stuck grease?

Any advice and words of wisdom is greatly appreciated, clear skies
WD40. Soak the bearings in there then rince and dry them and pack them back with bearing grease. If they're sealed bearings then leave them as is. For any other cleaning turp and a bucket with a brush.
Reply With Quote
  #4  
Old 04-10-2021, 08:27 PM
raf.serrano (Raf)
Registered User

raf.serrano is offline
 
Join Date: May 2020
Location: Melbourne
Posts: 27
Quote:
Originally Posted by Eldest_Sibling View Post
I remove Synta's factory glue-grease with charcoal-lighter fluid, used for grilling food outdoors. It's a light grade of kerosene, and cuts right through the old grease...

Attachment 281579

The CGEM is considered too complicated to work on by the average user, which is probably why you're having trouble finding renovation material. Of course, I would work on one regardless, so welcome to the DIY club.

There are folks working on theirs on YouTube...

https://www.youtube.com/results?sear...Celestron+CGEM
Wow there's a lot of resource when you remove the "hypertune" keyword thanks so much Alan.

Not sure though if I would pass beyond an average user, the only thing I was able to accomplish at the moment is to fix the play from an AZ-Gti RA and dec but then that is a tiny mount and fairly easy to disassemble

I'll also have a look at that charcoal-lighter fluid, I'm planning to clean and regrease the motor reduction gears as well if my comprehension can fathom how to access that

cheers mate!
Reply With Quote
  #5  
Old 04-10-2021, 08:30 PM
raf.serrano (Raf)
Registered User

raf.serrano is offline
 
Join Date: May 2020
Location: Melbourne
Posts: 27
Quote:
Originally Posted by multiweb View Post
WD40. Soak the bearings in there then rince and dry them and pack them back with bearing grease. If they're sealed bearings then leave them as is. For any other cleaning turp and a bucket with a brush.
Got it, thanks for the advise Marc, not sure before if I should use the grease removing kitchen chemicals asking around most likely saved the life of my mount haha
Reply With Quote
  #6  
Old 05-10-2021, 05:54 AM
Eldest_Sibling's Avatar
Eldest_Sibling (Alan)
Registered User

Eldest_Sibling is offline
 
Join Date: May 2017
Location: Mid-South, U.S.
Posts: 136
Quote:
Originally Posted by raf.serrano View Post
Wow there's a lot of resource when you remove the "hypertune" keyword thanks so much Alan.

Not sure though if I would pass beyond an average user, the only thing I was able to accomplish at the moment is to fix the play from an AZ-Gti RA and dec but then that is a tiny mount and fairly easy to disassemble

I'll also have a look at that charcoal-lighter fluid, I'm planning to clean and regrease the motor reduction gears as well if my comprehension can fathom how to access that

cheers mate!
You're most welcome. Do take photographs as you go along, documenting the process. Proceed slowly, patiently, photographing every little thing, and more besides.

I use this heavy-duty grade of Super Lube for re-greasing my mounts...

Click image for larger version

Name:	Super Lube3.jpg
Views:	347
Size:	50.5 KB
ID:	281584

Click image for larger version

Name:	Super Lube cartridge2.jpg
Views:	255
Size:	40.0 KB
ID:	281586

Click image for larger version

Name:	Super Lube cartridge3.jpg
Views:	330
Size:	58.7 KB
ID:	281585

But others have used others to good effect.
Reply With Quote
  #7  
Old 05-10-2021, 01:59 PM
traveller's Avatar
traveller (Bo)
Not enough time and money

traveller is offline
 
Join Date: Aug 2011
Location: Melbourne
Posts: 2,133
Raf have a search through cloudy nights as there may be some links there. I found a link in there for my CGX rebuild.
+1 for super lube.
Bo
Reply With Quote
  #8  
Old 06-10-2021, 02:53 AM
raf.serrano (Raf)
Registered User

raf.serrano is offline
 
Join Date: May 2020
Location: Melbourne
Posts: 27
Quote:
Originally Posted by Eldest_Sibling View Post
You're most welcome. Do take photographs as you go along, documenting the process. Proceed slowly, patiently, photographing every little thing, and more besides.

I use this heavy-duty grade of Super Lube for re-greasing my mounts...

Attachment 281584

Attachment 281586

Attachment 281585

But others have used others to good effect.
Thanks again Alan, have Superlube on the way, the grease and spray both with PTFE.
Reply With Quote
  #9  
Old 06-10-2021, 02:53 AM
raf.serrano (Raf)
Registered User

raf.serrano is offline
 
Join Date: May 2020
Location: Melbourne
Posts: 27
Quote:
Originally Posted by traveller View Post
Raf have a search through cloudy nights as there may be some links there. I found a link in there for my CGX rebuild.
+1 for super lube.
Bo
Thanks bo will have a look in Cloudy Nights as well.
Reply With Quote
Reply

Bookmarks

Tags
celestron, cgem, cgem rebuild, eq mount, mount

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 09:38 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement