Go Back   IceInSpace > Equipment > DIY Observatories

Reply
 
Thread Tools Rate Thread
  #21  
Old 01-06-2024, 04:08 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Dome base ring almost complete.

So, over the last two days I have been work on two parts of the observatory project. This thread is about the final stage of completing the Dome base ring which includes the lamination of the last plywood layer, patching the screw holes and joints with builder's bog, sanding and first coat of 4 or 6 of marine varnish.

Why marine varnish, I thought it was a good idea as it will seal the plywood and give a nice surface finish for the rollers to run on.

Cheers

P.S. I did go around and check and relevel the dome base ring to ensure it is with in tolerance and is somewhat level in all cardinal points. A process I will keep doing until the final plywood cover is applied.
Attached Thumbnails
Click for full-size image (20240531_133835.jpg)
157.9 KB86 views
Click for full-size image (20240531_142708.jpg)
141.9 KB101 views
Click for full-size image (20240531_144115.jpg)
154.0 KB91 views
Click for full-size image (20240531_150203.jpg)
156.7 KB99 views
Click for full-size image (20240601_100612.jpg)
167.2 KB139 views
Click for full-size image (20240601_155255.jpg)
169.6 KB70 views
Click for full-size image (20240601_160113.jpg)
118.2 KB120 views
Reply With Quote
  #22  
Old 01-06-2024, 04:39 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Shutter Frame

The other part of the project that I was working on today was the constructure of the Shutter frame. Same routine as with the dome base was to cut out 13 plywood arcs with an outside radius of 1258mm. Lay them out and align with a tangent arm.

Was thinking of constructing the ring on the pavement but with the treat of rain I move to the garage which was my original plan. The good thing with my garage it that I was able to use the expansion joints in the concrete to centre the tangent arm right where they cross at 90 degrees.

I only had to laminate two layers of plywood together, so the process was quite quick and having done it multiply time it get easier with the trimming, gluing and screwing.

Final task tomorrow is to divide the ring into two semi-circle than hopefully put some studs in to form the opening and attach it to the dome base ring. This will depend on the painting.

Cheers

P.S. The Shutter opening was scaled up to 690mm due to the fact I have scaled up the diameter of the dome from 2.3m to 2.6m

Also here is the link I used to get the right radius for the shutter frame. https://ambrbit.com/TrigoCalc/Sphere...ereCap.htm#cap
Attached Thumbnails
Click for full-size image (20240601_100623.jpg)
99.2 KB71 views
Click for full-size image (20240601_103105.jpg)
187.8 KB106 views
Click for full-size image (20240601_111342.jpg)
161.1 KB92 views
Click for full-size image (20240601_131902.jpg)
144.6 KB83 views
Click for full-size image (20240601_134347.jpg)
124.9 KB109 views
Click for full-size image (20240601_150236.jpg)
102.8 KB108 views
Reply With Quote
  #23  
Old 01-06-2024, 08:19 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
The big cut

Need to get the car back into the garage so decided to cut the shutter frame in half early.

Using the tangent arm, I made sure the Shutter fame ring was centred, then ran a string line across the circle ensuring it passed over the centre to give me a line to cut by. Also ran a string line 90 degrees to the first to mark in what will be the top of the semi-circle, tape measure help with squaring the lines.

Once done, cut line marked in then a quick cut with the saw. End result to evenly matched semi-circle.

Very happy with the result.

Cheers
Attached Thumbnails
Click for full-size image (20240601_195440.jpg)
76.1 KB100 views
Click for full-size image (20240601_201644.jpg)
74.9 KB134 views
Click for full-size image (20240601_203739.jpg)
98.5 KB111 views
Click for full-size image (20240601_204347.jpg)
84.4 KB124 views
Click for full-size image (20240601_204734.jpg)
173.3 KB131 views
Click for full-size image (20240601_204742.jpg)
153.6 KB137 views

Last edited by anthony2302749; 02-06-2024 at 08:31 PM.
Reply With Quote
  #24  
Old 02-06-2024, 07:17 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Shutter frame Construction.

Today's part of the project was to construct the Shutter frame proper. First task was to recheck the maths to ensure the height of the frame is correct in relation to the dome base ring and that the future dome ribs will fit correctly (I have an idea for that but have to wait till next weekend). Removed 36mm from each end of the Shutter semi-circle. After this task I got the desired height of roughly 1348mm (1258mm height of Shutter semi-circle plus 90mm for the support blocks not including the window packers)

I then made 3 by 1" thick plywood studs (Not entirely happy with the end result of two, they may get the flick) to secure the Shutter semi-circle parallel with each other and squared front and back. Final task was to add additional studs of 42 x 19mm Pine which I repurposed from an old screen which I had made years ago, and which was heading to landfill.

The Shutter width is 690mm (27.1") with and opening past zenith of 178mm (7"). Rule of thumb for the opening past zenith is half the aperture of the telescope diameter. Which of cause came from the web some were maybe Cloudy Nights.

Cheers

P.S. The Dome base ring got a final coat of marine varnish, four coats in total. Tomorrow with the help of my son, going to flip the dome base ring, centre, level and mount the Sutter Frame.
Attached Thumbnails
Click for full-size image (20240602_111940.jpg)
188.5 KB198 views
Click for full-size image (20240602_120044.jpg)
172.6 KB112 views
Click for full-size image (20240602_123335.jpg)
160.9 KB125 views
Click for full-size image (20240602_143045.jpg)
180.8 KB98 views
Click for full-size image (20240602_150517.jpg)
140.0 KB123 views
Click for full-size image (20240602_155158.jpg)
144.4 KB100 views
Click for full-size image (20240602_164741.jpg)
165.3 KB167 views

Last edited by anthony2302749; 02-06-2024 at 08:18 PM.
Reply With Quote
  #25  
Old 03-06-2024, 07:26 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
A flip and rejig.

This evening, flip the dome base ring, centred, levelled, ran a string line to obtain equal halves. Then measured ran a string line 90 degree to the first to obtain equal quarters. Remounted the Shutter frame and centred.

Still not liking how the Shutter frame end pieces which sit on the dome base ring look, I think I can come up with a neater solution.

Cheers
Attached Thumbnails
Click for full-size image (20240603_195852.jpg)
120.1 KB99 views
Click for full-size image (20240603_200810.jpg)
139.5 KB144 views
Reply With Quote
  #26  
Old 07-06-2024, 10:27 AM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,049
That's looking AMAZING!
The mention of marine varnish, I learnt a long time ago the quality in the timber and finish is what makes it last. I've tried the cheap options in the past for various projects, never again where timber and finishes are concerned.
Ah, my sister is visiting Melbourne from Queensland and sent me photos yesterday of clear blue skies, I dream of those things but rarely experience them, it raining again here for the past 3/4/5/...days.
Reply With Quote
  #27  
Old 07-06-2024, 04:48 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
First pair of ribs complete 4 to go.

The long weekend is a pond us, and for me more construction work on the dome.

Today's effort was to complete the pair of 90-degree Ribs. This of course involved more routing however the math on this was easy as the ribs are the same radius of the base ring.

So, for the pair of 90-degree ribs I need to cut out 6 plywood arcs. I started to assemble one by placing the plywood arcs on the dome base ring but found it didn't work the way I hoped. Only advantage was cutting the correct angle of 90-degree ribs which mate to the shutter frame. Went to method B, that is clamp two plywood arcs together, line the top to the shutter centre and line the bottom to the quarter mark, adjust to the desired length by loosening and re-clamping. Once I was happy, I added a small fudge factor in of 5mm in and glued and clamped all pieces together.

Once I had completed the first rib, check my work against the shutter frame and ring and made adjustment by trimming each end of the Rib until I had a nice fit. Rib one became templated for Rib two and I knock it out very quickly.

Once I had two complete Ribs, I clamped them on to the Shutter/dome ring Base. Made some further corrections in measurement regarding equal halves and quarters. After this I started to make 90-degree Blocks to use as brackets instead of metal ones, I think it looks nicer. Also gives me a point for clamping the plywood cover later on.

Cheers
Attached Thumbnails
Click for full-size image (20240607_102157.jpg)
189.1 KB104 views
Click for full-size image (20240607_113825.jpg)
118.0 KB76 views
Click for full-size image (20240607_113840.jpg)
181.8 KB162 views
Click for full-size image (20240607_120604.jpg)
198.5 KB52 views
Click for full-size image (20240607_124143.jpg)
163.1 KB74 views
Click for full-size image (20240607_142821.jpg)
188.3 KB132 views
Click for full-size image (20240607_145300.jpg)
171.3 KB111 views
Click for full-size image (20240607_163546.jpg)
167.1 KB102 views

Last edited by anthony2302749; 08-06-2024 at 07:39 PM.
Reply With Quote
  #28  
Old 08-06-2024, 02:47 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Another two pair of ribs knocked out.

Today's task was to fix the Shutter frame and 90-degree rib to the dome base ring. Plus, route out and assemble four 60-degree ribs.

Same method was used for 60-degree rib as with the 90-degree rib. But as the 60-degree rib attaches lower I need to measure down 210mm from the top of the shutter frame, more maths. Using a bevel square, I obtained the correct angle so that the rib sits flush to the shutter frame. Then with the help of some clamps I adjusted the 60-degree rib until I got the right length and top and bottom of the 60-degree rib sat flush. Glued, clamped and screw the rib together ensuring to leave a few extra millimetres as a fudge factor.

Bevelled the top end to get a nice flush fit, trimmed 5mm of the bottom and the first 60-degree rib was complete and ready to be used as a template for the other three.

The other three ribs have been constructed and are sitting on the decking.

Cheers
Attached Thumbnails
Click for full-size image (20240608_094315.jpg)
144.9 KB54 views
Click for full-size image (20240608_094322.jpg)
145.1 KB56 views
Click for full-size image (20240608_095502.jpg)
172.2 KB56 views
Click for full-size image (20240608_103303.jpg)
159.4 KB50 views
Click for full-size image (20240608_105346.jpg)
141.3 KB70 views
Click for full-size image (20240608_114352.jpg)
157.2 KB80 views
Click for full-size image (20240608_140612.jpg)
198.8 KB63 views
Click for full-size image (20240608_151511.jpg)
167.9 KB47 views

Last edited by anthony2302749; 08-06-2024 at 04:28 PM.
Reply With Quote
  #29  
Old 08-06-2024, 04:28 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Beginning to look like a dome.

Since my last post which wasn't that long ago, I have bevelled and trimmed the 60-degree ribs and clamped them into place. Beginning to look like a dome. Did make one cutting error with a rib, cut the bevel on the wrong end from where I had marked it, obviously forgot to "measure twice, cut once". However, had plenty of fudge factor to play with, so no real concern.

Next task is to fix the 60-degree ribs to the Shutter frame and dome base ring and get started on the four 30-degree ribs.

Cheers
Attached Thumbnails
Click for full-size image (20240608_155518.jpg)
150.5 KB66 views
Click for full-size image (20240608_165804.jpg)
143.5 KB46 views
Click for full-size image (20240608_165830.jpg)
151.9 KB48 views
Reply With Quote
  #30  
Old 09-06-2024, 07:44 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Getting somewhere now.

After a day visiting the Lume and lunch with the family I only had time to fix the 60-degree ribs into place and flesh out the final 30-degrees Ribs.

Same process as for the 90-degree ribs. Remeasure, drill, glue and screw the top of the 60-degree rib to the shutter frame and then remeasure, glue and nail the bottom of the 60-degree rib to the dome base ring. Job done.

Also fleshed out the last of the ribs, that being the 30-degree ribs. So, tomorrows job is assembling two pair of 30-degree ribs and hopefully have them fixed in place by the afternoon.

By the way, three sheets of 2400x1200x12mm plywood nearly made the distance had I not made some erroneous cuts on the second sheet while constructing the shutter frame. The piece of plywood that were intended for the shutter frame are now being repurposed as plywood brackets as seen in the pictures.

So, will need to buy roughly a 1200x1200x12mm plywood sheet to construct the ring that will be used to support the rollers and sit on the observatory wall structure. Will worry about that later.

Cheers
Attached Thumbnails
Click for full-size image (20240609_175203.jpg)
126.7 KB71 views
Click for full-size image (20240609_175216.jpg)
122.2 KB70 views
Click for full-size image (20240609_201511.jpg)
126.6 KB82 views
Click for full-size image (20240609_201518.jpg)
151.2 KB106 views
Reply With Quote
  #31  
Old 10-06-2024, 08:31 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Ran out of Plywood.

So, today's effort was to complete 30-degree ribs but alas I ran out of plywood to finish the last rib. What I did get to complete today, well at least three 30-degree ribs. All trimmed, glued and screw into position using the same method as all the other ribs in this build.

With the use of a plane and belt sander I bevel the top end of 30-degree ribs so that the sit flush with the Shutter frame. Pretty pleased with my carpenter skill so far.

Cheers
Attached Thumbnails
Click for full-size image (20240610_110504.jpg)
184.9 KB73 views
Click for full-size image (20240610_110508.jpg)
199.0 KB81 views
Click for full-size image (20240610_112746.jpg)
192.3 KB78 views
Click for full-size image (20240610_115233.jpg)
136.1 KB70 views
Click for full-size image (20240610_123738.jpg)
147.1 KB73 views
Click for full-size image (20240610_153818.jpg)
162.1 KB67 views
Click for full-size image (20240610_153826.jpg)
162.8 KB103 views
Click for full-size image (20240610_164722.jpg)
135.6 KB72 views
Reply With Quote
  #32  
Old 14-06-2024, 06:01 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
After buying another sheet of plywood the dome frame is finished.

Last rib when in this morning marking the end of the dome frame construction. Also sand down each rib and filled in the screw holes to get the frame ready for covering.
Attached Thumbnails
Click for full-size image (20240614_122840.jpg)
134.2 KB83 views
Click for full-size image (20240614_125642.jpg)
145.8 KB87 views
Click for full-size image (20240614_145447.jpg)
146.3 KB78 views
Reply With Quote
  #33  
Old 14-06-2024, 06:08 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Templates

So, with the finishing of the dome frame the next step is the covering of the dome. For this task I am creating three cardboard templates to be used to help cut out the 3mm plywood sheets. Two templates are complete the third one will be done tomorrow. By tomorrow afternoon should have several plywood panels cut out and attached to the dome frame.

Cheers
Attached Thumbnails
Click for full-size image (20240614_150433.jpg)
85.3 KB227 views
Click for full-size image (20240614_152649.jpg)
114.3 KB135 views
Click for full-size image (20240614_153934.jpg)
156.6 KB102 views
Click for full-size image (20240614_160838.jpg)
154.4 KB156 views
Click for full-size image (20240614_162049.jpg)
126.0 KB160 views
Click for full-size image (20240614_170403.jpg)
115.2 KB157 views
Click for full-size image (20240614_172301.jpg)
90.9 KB114 views
Reply With Quote
  #34  
Old 14-06-2024, 06:10 PM
croweater (Richard)
Don't Panic!

croweater is offline
 
Join Date: Feb 2015
Location: Mount Gambier, South Australia
Posts: 554
Quote:
Originally Posted by anthony2302749 View Post
Last rib when in this morning marking the end of the dome frame construction. Also sand down each rib and filled in the screw holes to get the frame ready for covering.
Looking good Anthony. You re going to have to restain your deck when you're finished
Cheers, Richard
Reply With Quote
  #35  
Old 15-06-2024, 04:18 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Quote:
Originally Posted by croweater View Post
Looking good Anthony. You re going to have to restain your deck when you're finished
Cheers, Richard
Reply With Quote
  #36  
Old 15-06-2024, 04:38 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
The trial and tribulations of applying the covering.

So today I was hoping to get a bit more done in the way of applying the plywood sheeting to the dome frame, however things did not go to plan.

Making the template was relatively easy and cutting the plywood sheeting not much of a challenge, however affixing the first segment went south quickly. In my mind I was hoping to be able to fold the plywood over the shutter frame, in practise I destroyed a good piece of ply. So back to the drawing board for a new idea.

The solution was to rip a piece of 40x19mm pine with the circular saw set at an angle of 22 degrees. Good thing is that the pine been sitting out in the weather and therefore quiet damp which makes it easy to bend into shape. Glued and clamp new 22-degree piece to the shutter frame, tacked with stables. Modified the template, cut out a new piece and put it into position once the glue had time to dry. Success, the piece went on nicely.

So, in the long run I manage to get two pieces attached today.
Attached Thumbnails
Click for full-size image (20240615_110606.jpg)
85.2 KB107 views
Click for full-size image (20240615_110741.jpg)
167.6 KB101 views
Click for full-size image (20240615_111735.jpg)
200.0 KB70 views
Click for full-size image (20240615_124846.jpg)
131.2 KB178 views
Click for full-size image (20240615_144538.jpg)
156.6 KB131 views
Click for full-size image (20240615_144543.jpg)
131.7 KB82 views
Click for full-size image (20240615_151017.jpg)
123.0 KB115 views
Click for full-size image (20240615_162145.jpg)
134.7 KB57 views
Reply With Quote
  #37  
Old 16-06-2024, 05:11 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Not so fun part of the build

So, since my thread I've been hard at work installing the 3mm Plywood panels. Let's say it is the least enjoyable part of the build as there is a lot of fiddly adjustment along with a bit of cursing and blood, put the drill into my finger.

Anyway, while I endeavoured to get the templates correct, thing didn't fall together as I intended hence the fiddly adjustments. The 22 degrees bevels were installed along the shutter frame, finish of the last two 30-degree panels. Then moved on the last three 60-degree panels (did one last night), these panel were a pain to do in regard to getting them to fit somewhat in line with 30-degree panels, a bit of trimming was required. So, all up installed 5 panels today, all glued screwed and stapled on.

Four more panels to go with one sheet of 3mm plywood left, will I make it.

Cheers
Attached Thumbnails
Click for full-size image (20240616_115842.jpg)
146.5 KB85 views
Click for full-size image (20240616_130831.jpg)
111.3 KB84 views
Click for full-size image (20240616_132156.jpg)
105.2 KB83 views
Click for full-size image (20240616_162836.jpg)
114.1 KB101 views
Click for full-size image (20240616_164652.jpg)
114.3 KB74 views
Reply With Quote
  #38  
Old 17-06-2024, 08:00 AM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,049
It's looking amazing Anthony but watch out for the finger and don't let it get infected. I've done it more times than I'm prepared to admit.
Reply With Quote
  #39  
Old 17-06-2024, 08:19 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
One side of the dome is complete.

Well skipped some formality this evening. Rip the last piece of 3mm ply for the last two panels. Ended up short by one piece, so need to purchase another sheet this week.

As you can see, I have completed one full side of the dome. I didn't get too pedantic with how well the panels aligned with each other, a mm or 3 is not going to be the end of the world. As for glue I have been using liquid nails as the adhesive, this was applied to the rib before the panel is placed into position. The panel was then clamp top and bottom and stabled down with furniture staples. (Tip I picked up from another thread on Cloudy Night, plus I own a Staple Gun plus compressor. Quick work.)

Future work will be to complete all the panelling, sand and fill joins with Builders Bog. More sanding than fiberglass all the joins, more sanding, than paint with good quality exterior paint.

Still a long way to go, plus there is still the shutter to design and build.

Cheers
Attached Thumbnails
Click for full-size image (20240617_170423.jpg)
89.3 KB94 views
Click for full-size image (20240617_170909.jpg)
85.2 KB125 views
Click for full-size image (20240617_170924.jpg)
87.8 KB116 views
Click for full-size image (20240617_205400.jpg)
85.9 KB120 views
Reply With Quote
  #40  
Old 20-06-2024, 06:53 PM
anthony2302749's Avatar
anthony2302749
Registered User

anthony2302749 is offline
 
Join Date: Aug 2005
Location: Melbourne
Posts: 507
Dome Cover coming to completion.

Today picked up the last sheet of 3mm plywood from Bunnings. To fit it into the car I had to cut it in to 3 pieces so took the necessary tools with me. Anyway, long story short, I was about to cut up the plywood only to find I left the circular saw battery at home. Thank God the tool shop had a demo battery for me to use.

So, after work I installed the last panel to complete both sides of the dome. Also place the first panel to cover the rear shutter frame of the dome. Another small panel and the dome will be completely ready for the next stage, which is to sand the joints and fill with Builders Bog.

School holidays next week so I will have more time on the build, progress will be much quicker.

Cheers
Attached Thumbnails
Click for full-size image (20240620_153139.jpg)
91.7 KB106 views
Click for full-size image (20240620_153151.jpg)
46.4 KB71 views
Click for full-size image (20240620_161902.jpg)
101.7 KB105 views
Click for full-size image (20240620_163834.jpg)
91.2 KB83 views
Click for full-size image (20240620_170446.jpg)
95.4 KB96 views
Click for full-size image (20240620_170457.jpg)
92.1 KB98 views
Click for full-size image (20240620_170918.jpg)
116.5 KB90 views

Last edited by anthony2302749; 20-06-2024 at 08:39 PM.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 09:12 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement