Go Back   IceInSpace > Equipment > DIY Observatories

Reply
 
Thread Tools Rate Thread
  #21  
Old 12-11-2024, 04:28 PM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,048
That looks good Simon!
I like the name too and remember the early image and the mention of wrestling the goat to get it out (or was it sheep, my memory is crap?)
Reply With Quote
  #22  
Old 13-11-2024, 10:10 AM
SimmoW's Avatar
SimmoW (SIMON)
Farting Nebulae

SimmoW is offline
 
Join Date: Jan 2014
Location: Tamleugh, Victoria, Australia
Posts: 1,410
Quote:
Originally Posted by astronobob View Post
That is a very fine and very cool caper there Simon,, A job well done,,, Makes a lot of sense to have a protected permanent rig
Yes it makes a huge difference! Plus a relatively easy build to gain more building experience.
Reply With Quote
  #23  
Old 13-11-2024, 10:14 AM
SimmoW's Avatar
SimmoW (SIMON)
Farting Nebulae

SimmoW is offline
 
Join Date: Jan 2014
Location: Tamleugh, Victoria, Australia
Posts: 1,410
Quote:
Originally Posted by Leo.G View Post
That looks good Simon!
I like the name too and remember the early image and the mention of wrestling the goat to get it out (or was it sheep, my memory is crap?)
Thanks Leo and others. Haha it was a sheep/lamb, but our larger obsies we are constructing have goats climbing all over the framework! Hence my other project of building an inner goat proof fence with electric fence, Claymores and auto mini guns 😂
Reply With Quote
  #24  
Old 13-11-2024, 03:08 PM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,048
I was offered a small goat the other day free (begged to take it or both), little black things which gored the property owners arm. I've not seen the horns like these things had, they looked quite menacing and dangerous, having had a big, old goat when I was younger but I do know they'd eat my long grass and destroy everything they can't eat and declined the offer.
Reply With Quote
  #25  
Old 14-11-2024, 05:42 AM
SimmoW's Avatar
SimmoW (SIMON)
Farting Nebulae

SimmoW is offline
 
Join Date: Jan 2014
Location: Tamleugh, Victoria, Australia
Posts: 1,410
Very wise Leo!! My partner breeds them, they breed like, well, goats, and when young can be hilarious and cute, but once older, are cunning and yes not compatible with astronomy equipment.

I once had a trailer need to be repaired twice, from goats eating the electrical wiring!

I often threaten to mulch their pasture, while they're still in it 😂.

But no, I still love em, if only for their ability to teach me new fencing techniques.

Luckily this mini obs is in our residential block, no goats nearby, just a couple of those pesky labs and large Maremma dogs. Snakes the biggest risk.

Oh just uploaded a video showing the setup!

https://youtu.be/nJyGfsyC1Fk?si=EXA_WKgjrLjtN5DE
Reply With Quote
  #26  
Old 15-11-2024, 01:53 PM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,048
My yard is not good for astronomy, sloping ground, huge trees in neighbouring yards, LED street lights that light my back yard up like a Friday night football game and mountains to the east and west but, NO SNAKES.
I lived at the bottom of a mountain locally previously and had a creek (concrete piped by council) across the road and the Tiger snakes used to come down from the mountains and through my yard to get to the water. Mostly not a threat but I had to keep my grass short, one bite cost me a fortune to save my cat and I was very cautious in the yard at night because I spent a lot of time out under the stars. I've nearly trodden on big Tiger snakes a few times and am grateful I didn't (I owe my life to my then neighbours teenage daughter I'd been chatting to about her school project over the fence and she saw the 6' Tiger snake I was about to jump down onto, I'll never forget and told her husband if I ever win big I'll be paying their mortgage out plus some).


When younger I had no problem catching snakes by hand, usually to relocate them. I was quicker than them every time (Tiger snakes, red bellies, copper heads never a brown snake though) but after being diagnosed with a heart condition at 40 I decided while I may still be faster than them one bite I wasn't coming back and I stopped.
I grew up in a swamp area and there were always snakes. I always had a good torch and wore gumboots around the yard at nights and survived several boot strikes where I'd miss-stepped in the dark or just didn't see them there. Heavy foot steps and they usually get out of your way unless they have a nest.
Reply With Quote
  #27  
Old 18-11-2024, 04:47 PM
Astro1969 (Craig)
Astro Junkie

Astro1969 is offline
 
Join Date: May 2023
Location: Maitland
Posts: 6
Just last week I was eyeing off an IBC at work wondering if I could use it at home...
Reply With Quote
  #28  
Old 19-11-2024, 08:25 AM
SimmoW's Avatar
SimmoW (SIMON)
Farting Nebulae

SimmoW is offline
 
Join Date: Jan 2014
Location: Tamleugh, Victoria, Australia
Posts: 1,410
Quote:
Originally Posted by Astro1969 View Post
Just last week I was eyeing off an IBC at work wondering if I could use it at home...
Haha, I'm even stating to think that with a welder (I'm shocking at it, but it works...), 4 cut up would make a massive new project!
Reply With Quote
  #29  
Old 19-11-2024, 10:54 PM
Leo.G (Leo)
Registered User

Leo.G is offline
 
Join Date: Nov 2016
Location: Lithgow, NSW, Australia
Posts: 1,048
Quote:
Originally Posted by SimmoW View Post
Haha, I'm even stating to think that with a welder (I'm shocking at it, but it works...), 4 cut up would make a massive new project!
SAFETY GEAR:


First: Full cotton overalls, not nylon, full arm and leg coverage, welding emits strong UV which leads to cancers and leukaemia. No nylon clothing, it goes up fast, another thing learnt from experience wearing nylon overalls in an employment position and being taught to weld as part of my job. My saviour was full cotton shorts under the nylon overalls or the family jewels would have been torched. This was many years before I studied fabrication engineering but I never forgot and had some severe burns on my hands from extinguishing the flames and melting nylon overalls.


Second: Good quality welding gloves.


Third: Work boots.


Fourth: Good woollen socks, nylon socks can leave nasty burns when slag flies down the boot (first hand scars and experience). Spats around the top of boots (gators) are good to stop slag entering boots.
A quality face shield and leave a cover on when chipping slag and grinding but I have a different shield for grinding so I don't pit my expensive mask.


DO NOT stand bare footed on wet grass while clamping steel in place with other bare foot and striking an arc. Lesson learnt early on while studying electrical and electronics engineering and I SHOULD have known better. I only did it once though, one bare foot in puddle, one bare foot on steel..
A new welding rod can be bent for convenience and you can hold the rod with a good glove to steady the welds to get a feel, good gloves you won't get burnt and it's easier than trying to strike a full length rod. I keep my small scrap rods fro doing tacks, it's easy to do. I also slap a piece of scrap on top for a striking plate, strike the rods on plate first to get heat then move immediately to the weld point. It does simplify welding with an arc welder.



A MIG is easier if you have access, gasless is good out in the paddock if it's not too breezy. Gas tends to do better welding (Argon mix) but no good with a breeze unless shielded from the wind. If you have access to a MIG and go gasless remember the polarity of the welder must be changed before switching from gas to gasless. An arc welder will do it, just try to maintain a constant ark length and hold the rod at approximately 15 degrees off upright perpendicular to the job for best results and arc rods are dragged not pushed while MIG is generally pushed but a lot of people will drag them too. [b]Like painting, a clean surface is the trick to good welding and if welding galvanised steel grind the galvanising off before welding because the sulphur fumes are highly toxic.


Weld DOES NOT burn through paint, grease and galvanising. It leaves inclusions in the weld and an added weakness. No paint, no oil or grease and definitely no galvanised coatings. If Gal is the required finish, cold gal painted on after welding is fine and always chip off the slag to see the quality of the weld, don't paint over it.


My best advice, a good welding mask, these electric things are great but not the cheapest Aldi things you can get. They too are probably OK if you have good eyes, for me I have a very expensive Uniimig mask from memory, an RWX8000 but my mask ranges from shade 5 right up to 13), not necessary for most Mig or arc welding but I need to get back into TIG which I haven't done for over 20 years since doing fabrication engineering. I used to excel on the TIG doing alloy.
Now my sight makes it terribly hard to see the weld pool so I do very little welding but have a go to $49 Aldi arc welder (reduced on special), a little inverter I use for just about everything because I can carry it on my little finger and weld 3/4" bar with ease. Thin materials are easy with it too if you understand frequent tacking where the tacks draw the heat from the line of weld as you move forward. My 200Amp Mig is not an inverter and weighs over 30KG and is heavy to lump around, gas or gasless. If I knew how to weld I'd weld up a trolley for it, lol.


https://www.weld.com.au/product/unim...v=6502139931c4


https://external-content.duckduckgo....efc&ipo=images


I also have a near identical other brand purchased from Repco on sale, also a very good mask and if my son and I are out playing together I always know his eyes are safe.



There's lots of tips available online for welding, more is not necessarily stronger and you can tell the quality of the job by the sound of the arc, unstable arc with constant varying distances between the tip and the job makes quite the spattering sound. A good weld you can hear the buzz of a steady arc. The tack welding of entire surfaces as often seen on youtube are not good welds and if you don't like the weld or think it's not strong enough it's easy to grind out and redo.
Maintaining a steady arc length comes with practice as does welding speed for the materials you're welding. I'm ALWAYS VERY rusty when I haven't done any welding for long periods which is often but I keep scrap thick plate here I can run a dozen or so welds along the length till I get my eye and hand in. It's easy ground off if the plate is needed for something.


Another tip, warm the rods up in a tray in the oven for 15 minutes at around 140-180 before welding they strike up easier (you can wrap them in foil to keep the heat in when taken out too) and never use old, wet rods. They too can be dried in an over to recover them and remove dampness but I don't remember times or temperatures but it's easy to find online.


Good luck!

Last edited by Leo.G; 20-11-2024 at 07:15 AM.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 10:00 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement