Go Back   IceInSpace > Equipment > DIY Observatories

Reply
 
Thread Tools Rate Thread
  #41  
Old 15-05-2022, 03:43 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
this might be a bit boring, unless your into DIY domes I guess .
A bit of a milestone today, finally got the slot door and its wheels sorted, along with making it rainproof, its been a bit of a challenge.

Turns out bending PVC angle with a heat gun is easier than al, it turns to putty, difficult to handle melted, but you can do anything with it.

So I used angle al for strength (wheel guides)and angle PVC to rainproof. Including U section (Yeah, bending U section, who would've thunk that was a thing )
The pic is pretty rough, but will all will pan out in post. Ill use Topaz magic

I lost 2 days of stuffing around with adhesives thinking that would look cleaner than screws and pop rivets. What a disaster, slippery, al moved all over the place and what a mess, my hands will be black for weeks. Liters of turps to remove and back to trusty screws and pop rivets.

Round everything continues to be a painful headspin in every way possible (All structural materials are supplied flat, nothing is usable out of the shop).
But I must say, im OK with it, occupies the grey matter
Attached Thumbnails
Click for full-size image (Dome slot door wheel.jpg)
148.0 KB163 views

Last edited by Bassnut; 15-05-2022 at 04:12 PM.
Reply With Quote
  #42  
Old 16-05-2022, 10:07 AM
strongmanmike's Avatar
strongmanmike (Michael)
Highest Observatory in Oz

strongmanmike is offline
 
Join Date: May 2006
Location: Canberra
Posts: 17,152
Looks professional in that close up, nice

Mike
Reply With Quote
  #43  
Old 16-05-2022, 10:23 AM
sheeny's Avatar
sheeny (Al)
Spam Hunter

sheeny is offline
 
Join Date: Jun 2005
Location: Oberon NSW
Posts: 14,288
Well done Fred.


As an engineer I appreciate the challenges of your design, and I'm following with interest. Nice job on the bending.


Al.
Reply With Quote
  #44  
Old 16-05-2022, 03:47 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Quote:
Originally Posted by strongmanmike View Post
Looks professional in that close up, nice

Mike
Thanks Mike .Professional . I wont show a pic of the outside yet, its too embarrising, much adjusting was done, so many extra holes .

Quote:
Originally Posted by sheeny View Post
Well done Fred.


As an engineer I appreciate the challenges of your design, and I'm following with interest. Nice job on the bending.


Al.
Thanks Al. As an engineer, you must groan at what hackers like me do . Everything is from bunnings and hand tools, its sooo time-consuming. I bet theres a 1000 better ways to do this but I DONT CARE. Im dodgy and proud

Today, guide rollers.
Attached Thumbnails
Click for full-size image (guide rollers.jpg)
140.5 KB131 views
Reply With Quote
  #45  
Old 18-05-2022, 05:28 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Today, drive for the slot door.
Rack and pinion is easy for a ROR, straight rack cut to length and a gear to match.
Curved rack for a dome is a bit of a problem, Id hate to think what a custom diameter curved rack would cost. I see flexible rack for sale but for huge money, and it seems to me the spec would change the more it was curved.
Anyways, i thought id post this update as its as it solved a problem unique to domes. And I havent seen this solution on the net.
ABS 3d printing is not suited to small engineering mechanical parts, so I made the rack and gear big and chunky. The gear goes onto a 6mm gearbox shaft with a flat. That would last 5 seconds before stripping the ABS and spinning. So I alradited a metal knob with a grub screw in it into the gear, so strong.
Ill use the same rack but a different diameter for the dome drive. The rack was printed in sections (size the printer can take)that can be easily be bolted together. Those segments BTW can be printed by many 3D shops in OZ in 5 days for about $10ea. I will use about $50 in ABS stock on rack and pinions for the whole project. The $20 motor/gearbox from ebay in the pic also has an encoder attached, so if something goes wrong whilst opening /closing the controller will know immediately and alarm.
Attached Thumbnails
Click for full-size image (Rack and pinion A v8.jpg)
138.9 KB101 views
Click for full-size image (Door rack and pinion.jpg)
157.3 KB142 views
Click for full-size image (Slot door gearjpg.jpg)
188.8 KB135 views
Reply With Quote
  #46  
Old 18-05-2022, 09:51 PM
Joshua Bunn's Avatar
Joshua Bunn (Joshua)
Registered User

Joshua Bunn is offline
 
Join Date: Oct 2011
Location: Albany, Western Australia
Posts: 1,459
This is very cool, Fred. wonderful ingenuity and it looks great.
Reply With Quote
  #47  
Old 03-06-2022, 04:23 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Thanks Joshua .
Small update.
I taped the segment joints up with Byute Flash. Got a bit worried with the wrinkly look, but with 2 coats of flat primer it's looking ok, ill use many flat white metal paint top coats. Flat paint hides imperfections.
The inside is painted with flat black Dulux Metal shield epoxy enamel. This is SERIOUS paint. The pic shows just one coat of this flat black enamel over white primer. Never before have i seen such coverage of black top coat over white!. One coat to my surprise will do!.
Ive always liked Dulux for pigment density, but this is nuts. It was very thick, possibly due to the temp being 10 deg and twice as much paint used over coverage stated on the can. Lesson learned, paint metal when its cold, half the work!.
The 3D printed rack fitted to the slot door worked a treat on test .
Attached Thumbnails
Click for full-size image (Dome inside paint.jpg)
175.4 KB123 views
Click for full-size image (Dome undercoat.jpg)
156.7 KB123 views
Click for full-size image (flash on segments.jpg)
181.2 KB146 views
Click for full-size image (slot door with rack.jpg)
139.0 KB117 views
Reply With Quote
  #48  
Old 04-06-2022, 05:34 AM
strongmanmike's Avatar
strongmanmike (Michael)
Highest Observatory in Oz

strongmanmike is offline
 
Join Date: May 2006
Location: Canberra
Posts: 17,152
Wow looking good Fred, you're having fun, huh?

Mike
Reply With Quote
  #49  
Old 04-06-2022, 07:23 AM
LonelySpoon (Neville)
Registered User

LonelySpoon is offline
 
Join Date: May 2022
Location: Manton
Posts: 255
That sealant is a good way to go, Fred.

It's all coming along nicely.

N
Reply With Quote
  #50  
Old 04-06-2022, 08:00 AM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Thanks Mike and Neville.
More challenging than fun id say .
Yes, the flashing appears to be a good guess, I couldn't think of any other way that wouldn't look worse, given my skill set .
Reply With Quote
  #51  
Old 04-07-2022, 04:28 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Progress. Dome base built using mini ripple gal. Very light, flexible and stiff once screwed on. The rail for the dome concave rollers was easier than expected to fit. Rather than bent angle, flat 3mm al bar was much easier to bend
and fit with angle brackets, stiff as. Its true within a 1mm or so.
Attached Thumbnails
Click for full-size image (base door.jpg)
177.0 KB115 views
Click for full-size image (Dome base.jpg)
169.0 KB99 views
Click for full-size image (base rail.jpg)
116.6 KB104 views
Reply With Quote
  #52  
Old 04-07-2022, 07:48 PM
Startrek (Martin)
Registered User

Startrek is offline
 
Join Date: Dec 2017
Location: Sydney and South Coast NSW
Posts: 5,990
Fred,
Brilliant design and clever use of ripple gal , really strong and easy to wrap and screw
Looks great !!
My only observation , being an Obs I’d be using stainless 302 or 316 fasteners and alum small angles etc… like I used in my NexDome. Plated and even gal screws and small brackets rust out after a couple of years , even quicker when your Obs is 200m from the beach like mine is. Salt air is a killer on cheap plated and gal fasteners etc… from China.

Cheers
Martin
Reply With Quote
  #53  
Old 05-07-2022, 08:37 AM
LonelySpoon (Neville)
Registered User

LonelySpoon is offline
 
Join Date: May 2022
Location: Manton
Posts: 255
Nice base, Fred!
Two observations:
1. Instead of brackets and the associated electrical differential causing breakdown /rust, I routed a groove in the base and dropped the ring into that.

2. A year later i ripped that out and replaced it with a hoop of rolled tube, with skateboard bearings. Almost no friction, can turn it with one hand.

Getting tube rolled for my 3m diameter dome cost only $158.

Neville
LSO
Reply With Quote
  #54  
Old 05-07-2022, 10:33 AM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Thanks Martin and Neville

I hadn't thought of the corrosion or rust damn it, although im aware of electrical differential causing breakdown. It was hovering in the back of my mind for a little while but I barged on regardless.

Im not doing this all again, but i will bury everything in metal paint now. This should last until i leave this mortal coil.

I had thought of rolled tube, done by a local shop, but it sounded expensive, i didnt realise it would be that cheap!. I dont have a router or be able to make a slot accurate enough for the ring either.
Ive tested a concave roller on this rail, very smooth and friction free, better than i thought, so I bought a bunch, adjustable.
Reply With Quote
  #55  
Old 05-07-2022, 04:14 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Put the dome on the base for the 1st time today (no wheels yet, or rain cover between the dome and base). Its looking a bit janky still, no top coat paint yet. Suddenly realised access might be a pain with the base door, so ill fit a hatch to the other side of the slot (not shown) to allow just stepping in
To give scale, its 1900mm high
Attached Thumbnails
Click for full-size image (Dome on base A.jpg)
146.3 KB130 views

Last edited by Bassnut; 05-07-2022 at 04:27 PM.
Reply With Quote
  #56  
Old 05-07-2022, 08:50 PM
xelasnave's Avatar
xelasnave
Gravity does not Suck

xelasnave is offline
 
Join Date: Mar 2005
Location: Tabulam
Posts: 16,866
That is brilliant Fred great effort.
Alex
Reply With Quote
  #57  
Old 10-07-2022, 11:12 AM
marc4darkskies's Avatar
marc4darkskies (Marcus)
Billions and Billions ...

marc4darkskies is offline
 
Join Date: Mar 2007
Location: Quialigo, NSW
Posts: 3,141
Looking good Fred!!

Use a hose to simulate a rain storm to make sure you haven't overlooked any sneaky water ingress points!
Reply With Quote
  #58  
Old 10-07-2022, 02:43 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Thanks Alex and Marcus.
Absolutely ill be rain testing, was always the plan. Why would you mention this?, no faith?, doubting my vast building skills?

Today I fitted the adjustable wheels (for sliding doors, from bunnings). Was totally surprised how well that went, the dome rolls very smoothly with a finger push.

The quick-release hatch allows very easy step-in access. I was concerned given the small size of the dome that access/standing inside would be a problem. its not.
Attached Thumbnails
Click for full-size image (Dome wheel.jpg)
139.6 KB103 views
Click for full-size image (Dome hatch.jpg)
159.8 KB93 views
Reply With Quote
  #59  
Old 10-07-2022, 04:31 PM
hrcoleman66 (Hugh)
Registered User

hrcoleman66 is offline
 
Join Date: Mar 2022
Location: Geelong
Posts: 31
Wow, That's progress!

Looks like the conversations standing around at ASOG have born fruit.

BTW, we missed you last week. I was all ready to offer you a seat as soon as you walked through the door.

Seriously though, Careful of those rollers. Exposed to UV, they get brittle and crack.

Cheers,

Hugh
Reply With Quote
  #60  
Old 11-07-2022, 02:41 PM
Bassnut's Avatar
Bassnut (Fred)
Narrowfield rules!

Bassnut is offline
 
Join Date: Nov 2006
Location: Torquay
Posts: 5,064
Thanks Hugh, yes progress.
A rain skirt will go round the dome base. The wheels won't be exposed.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 08:30 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement