Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rate Thread
  #61  
Old 11-04-2024, 08:55 PM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
The heating ring for the finder is done and installed.
It has 55 ohms resistance and that dissipates about 2.6 watts of heating power at 12V.
Attached Thumbnails
Click for full-size image (FinderHeater1.JPG)
80.6 KB113 views
Click for full-size image (FinderHeater2.JPG)
100.0 KB67 views
Click for full-size image (FinderHeater3.JPG)
155.1 KB93 views
Reply With Quote
  #62  
Old 22-04-2024, 04:27 PM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
Last night I achieved first light of sorts.
After fine tuning the polar alignment, using a broomstick as a crowbar for nudging the pier supports, I went on to tweak the collimation and finally I even did a bit of lunar imaging.
It wasn't smooth sailing though. The mount in this configuration is much more prone to vibrations and resonances. I was driving the RA axis with an Arduino Uno/DRV8825 and getting vibrations that were interfering with the imaging.
Once I changed from 1/16 micro stepping to 1/32 and adjusted the current draw, things were ok, but I will need to do some vibration dampening work.
Attached Thumbnails
Click for full-size image (Back1.JPG)
162.4 KB98 views
Click for full-size image (Back2.JPG)
172.5 KB69 views
Click for full-size image (FirstLight1.jpg)
195.1 KB128 views
Reply With Quote
  #63  
Old 22-04-2024, 07:24 PM
JA
.....

JA is offline
 
Join Date: Oct 2016
Location: Melbourne, Australia
Posts: 3,024
Stefan, you went to the moon last night

Best
JA
Reply With Quote
  #64  
Old 22-04-2024, 08:36 PM
Joshua Bunn's Avatar
Joshua Bunn (Joshua)
Registered User

Joshua Bunn is offline
 
Join Date: Oct 2011
Location: Albany, Western Australia
Posts: 1,478
Thanks fir the updates, Stefan. I'm enjoying following. Crisp capture of the moon!
Reply With Quote
  #65  
Old 23-04-2024, 11:33 AM
Andy01's Avatar
Andy01 (Andy)
My God it's full of stars

Andy01 is offline
 
Join Date: Mar 2012
Location: Melbourne
Posts: 3,278
Very impressive first light Stefan, I imagine the results will be spectacular once you've sorted out the remaining niggles.
Reply With Quote
  #66  
Old 23-04-2024, 07:08 PM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
Quote:
Originally Posted by JA View Post
Stefan, you went to the moon last night

Best
JA
I'm afraid, this it is the only way for me to space travel. I was born 50 years too soon, otherwise I would be lining up to get on Musk's Starship.

Quote:
Originally Posted by Joshua Bunn View Post
Thanks fir the updates, Stefan. I'm enjoying following. Crisp capture of the moon!
Thanks Josh, it was a difficult capture as I was only able to correct the RA drift and the Moon drifts in both axes. I have ordered a cheap CNC shield that I will write some code for, and I will be able to make DEC corrections too. On the longer run, I will use a OnStep controller, just at the moment I don't feel like sorting out the multitude of versions that exist.

Quote:
Originally Posted by Andy01 View Post
Very impressive first light Stefan, I imagine the results will be spectacular once you've sorted out the remaining niggles.
Thanks Andy, the main niggles will be with the recoating of the primary mirror as my vacuum chamber can fit max 10" mirrors.
Reply With Quote
  #67  
Old 25-04-2024, 08:27 AM
Rod
Registered User

Rod is offline
 
Join Date: Sep 2006
Location: Mount Martha
Posts: 375
Looks really impressive Stefan. Despite your concern about remaining niggles, the Moon image looks terrific. I’m looking forward to seeing more images from it.

Rod
Reply With Quote
  #68  
Old 26-04-2024, 07:37 AM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
Quote:
Originally Posted by Rod View Post
Looks really impressive Stefan. Despite your concern about remaining niggles, the Moon image looks terrific. I’m looking forward to seeing more images from it.

Rod
Thanks Rod,

I posted another image, from the same night, in the solar system section.

I also found a mistake in my Arduino code that was contributing to the drift in the tracking.
Reply With Quote
  #69  
Old 09-05-2024, 06:23 PM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
I received the CNC shield V3 that I had ordered, and I can start writing code for it.
Amazingly it cost $10, including 4 stepper controllers.

The old hand paddle worked so well for over 20 years that I will retain it for the Arduino based controller. I only need to change the wiring.
Attached Thumbnails
Click for full-size image (Controller1.JPG)
176.8 KB67 views
Reply With Quote
  #70  
Old 10-05-2024, 09:46 AM
iborg's Avatar
iborg (Philip)
Registered User

iborg is offline
 
Join Date: Feb 2015
Location: Lynbrook, Australia
Posts: 653
Hi Stefan


This this is Philip, with the binoculars. Thank you for help on the day and for showing me your scope.


As I said, looking very good indeed!


I expect you are well aware of this, but, just in case, you should set the current limit for the stepper motor on the driver.


A link showing this is here, about 3/4 down the page.


Have fun


Philip
Reply With Quote
  #71  
Old 10-05-2024, 09:51 AM
Joshua Bunn's Avatar
Joshua Bunn (Joshua)
Registered User

Joshua Bunn is offline
 
Join Date: Oct 2011
Location: Albany, Western Australia
Posts: 1,478
Nice Stefan,


Is this a manual machine to CNC conversion?
Reply With Quote
  #72  
Old 10-05-2024, 10:53 AM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 939
Quote:
Originally Posted by iborg View Post
Hi Stefan


This this is Philip, with the binoculars. Thank you for help on the day and for showing me your scope.


As I said, looking very good indeed!


I expect you are well aware of this, but, just in case, you should set the current limit for the stepper motor on the driver.


A link showing this is here, about 3/4 down the page.


Have fun


Philip
Thanks Philip, yes I have been using the DRV8825 drives for a while on my DIY engraver, with the same CNC shield. With the small NEMA17 motors I set the current limit just a bit above 1A.

Quote:
Originally Posted by Joshua Bunn View Post
Nice Stefan,


Is this a manual machine to CNC conversion?
Josh, this CNC shield is open source, and it is used for all sorts of DIY engravers and 3D printers. The firmware for CNC control is available from the GRBL website. I am writing my own firmware for the telescope control.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 07:54 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement