Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rate Thread
  #41  
Old 25-08-2017, 07:53 AM
Astrofriend's Avatar
Astrofriend (Lars)
Registered User

Astrofriend is offline
 
Join Date: Aug 2017
Location: Stockholm, Sweden
Posts: 478
This was really interesting and useful.

When I upgraded my refractor with 2.5" flatfield flattener and later a 3" I had big problems until I got the right parts.

You can read here what threads I had to use.

2.5" ff + reducer:
http://astrofriend.eu/astronomy/proj...refractor.html

and

For the 3" ff:
http://astrofriend.eu/astronomy/proj...flattener.html

I will later upgrade the 3" ff with an off-axis adapter, then it starts all over again to find correct parts, not only the threads, they must be of the correct lenght also.

Maybe I shall collect all threads in a table later?

ps.
I think I have a 1/2" bolt to my EQ6 Synscan Pro mount, not M12, at least I bought a 1/2" recently. I will check it up later.

/Lars
Reply With Quote
  #42  
Old 31-08-2017, 08:00 PM
Astrofriend's Avatar
Astrofriend (Lars)
Registered User

Astrofriend is offline
 
Join Date: Aug 2017
Location: Stockholm, Sweden
Posts: 478
Hi,
Now I have collected some of the threads sizes that I have come in contact with in this table:
http://astrofriend.eu/astronomy/adap...s-threads.html

I will add more of them later.

/Lars
Reply With Quote
  #43  
Old 09-01-2019, 03:18 PM
peterskye (Peter)
Registered User

peterskye is offline
 
Join Date: Jul 2007
Location: Ulladulla, NSW Australia
Posts: 7
Good explanation of Astronomical Threads

This item was posted on the web in Sept 2018. It is fairly comprehensive.


https://agenaastro.com/astronomy-threads-explained.html


Peter Skye
Reply With Quote
  #44  
Old 09-01-2019, 05:12 PM
Saturnine (Jeff)
Registered User

Saturnine is offline
 
Join Date: Jul 2008
Location: Wollongong
Posts: 2,258
The Agena-Astro article is , if not the definitive article, is a very comprehensive rundown on most of the thread sizes most of us are going to encounter in our astro gear.
Thanks for posting Peter.
Reply With Quote
  #45  
Old 17-05-2019, 06:51 AM
Wavytone
Registered User

Wavytone is offline
 
Join Date: Jul 2008
Location: Killara, Sydney
Posts: 4,147
Precision nuts, screws & custom machining

While looking for nylon screws with knurled knobs I came across this source https://www.accu.co.uk/en/

What’s interesting is they also can make custom small parts, which I’ll try shortly.
Reply With Quote
  #46  
Old 16-06-2019, 05:38 PM
tempestwizz's Avatar
tempestwizz (Brian)
Registered User

tempestwizz is offline
 
Join Date: Jun 2005
Location: Vientiane, Laos
Posts: 236
I appreciate the effort that has gone into producing this thread. But did I miss something somewhere, or is it implied?
I haven’t seen included any reference to the angle of the threads, ie the thread depth.
I have acquired two sets of thread cutting tools for my lathe (internal, and external) one set is for a 65 degree and the other is for 55 degrees. I’m not sure if there are other angles used, but I have been assuming one is for metric threads and the other for imperial threads.
Maybe someone more learned than myself can confirm these parameters.
Reply With Quote
  #47  
Old 16-06-2019, 06:31 PM
alval (Alan)
Registered User

alval is offline
 
Join Date: Jun 2017
Location: Northern Adelaide
Posts: 73
Hi Brian,
British imperial threads are 55 degree threads BSW and BSF etc. The other imperial ( fractional and tpi) threads used in america and elsewhere such as UNC and UNF are 60 degree threads the same as metric threads being 60 degrees.
Al
Reply With Quote
  #48  
Old 16-06-2019, 09:48 PM
Astrofriend's Avatar
Astrofriend (Lars)
Registered User

Astrofriend is offline
 
Join Date: Aug 2017
Location: Stockholm, Sweden
Posts: 478
About metric threads, maybe this helps:

https://en.m.wikipedia.org/wiki/ISO_metric_screw_thread

Lars
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 07:25 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement