Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rating: Thread Rating: 12 votes, 4.92 average.
  #301  
Old 22-07-2017, 01:42 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Smile Gugolz #55

Quote:
Originally Posted by nobby2 View Post
I have since ordered some Gugolz Pitch #55 from GotGrit.com suitable to my current working temperature of 16C.
Good move. Gugolz #55 is the one I use at working temps around 10C, (I add a small amount of Stockholm tar to it, to modify it to about equivalent to #50 [or slightly lower] for the lower temps I work at). Gugolz is nice to work with. I used resin (rosin?) moderated with pure turps and beeswax way back in the 1960's (loved the smell), it worked ok if one got the balance right with the ingredients for working temperatures.

Stephen.
Reply With Quote
  #302  
Old 22-07-2017, 04:38 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Image record as promised from pervious post. I am attempting to polish an 8 inch mirror. I was using Tropical Resin Lap. The first attempts had way to many bubbles. The second attempt with the addition of more Castor Oil was much improved however only lasted one hour before it broke up. Obviously too hard and brittle. I have since ordered some Gugolz Pitch #55 from GotGrit.com suitable for my current working temperature of 16C.
Attached Thumbnails
Click for full-size image (first-attempt-to-many-bubbles.jpg)
202.7 KB129 views
Click for full-size image (Second-attempt-with-more-castor-oil.jpg)
201.2 KB109 views
Reply With Quote
  #303  
Old 25-07-2017, 03:50 PM
noodles468's Avatar
noodles468 (Jared)
Registered User

noodles468 is offline
 
Join Date: Jun 2015
Location: Bacchus Marsh VIC
Posts: 6
I recently had a go at the 'tropical' lap myself. My problems were different to yours though Neil, went overboard with the castor oil and now have a lap which is easy to cut channels into, but which I fear is much too soft. Think I will give it a few more goes with the resin to see if I can get it right before I give in and go with pitch.

My lap pictured here, freshly poured (but prior to trimming).
Attached Thumbnails
Click for full-size image (WP_20170219_001.jpg)
188.3 KB100 views
Reply With Quote
  #304  
Old 11-08-2017, 06:55 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Mirror polishing

Measuring progress polishing an 8 inch mirror. First picture has curved rough lines with scratches. The second picture is straightening up and looking even with some fine scratches. The target is to create a spherical mirror befor fine turning it into a parabolic mirror.
Attached Thumbnails
Click for full-size image (IMG_2178-small.jpg)
37.6 KB73 views
Click for full-size image (IMG_2207-small.jpg)
49.2 KB83 views

Last edited by nobby2; 20-08-2017 at 03:58 PM.
Reply With Quote
  #305  
Old 13-08-2017, 05:49 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Looks like your moving in the right direction Neil. How many LPI is the Ronchi grating? You might want to consider reducing pic size a little. I use "paint" function to size my pics. My camera is a basic Canon A1200 (12.1 Mega Pixel). I do the 20% fix to give nice size pics for the forums.

Stephen.
Reply With Quote
  #306  
Old 14-08-2017, 09:07 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Thanks Sopticals for the hint on pic sizes. I am in the figuring stage using 65 lines per inch. I also have 85 and 133 that I may get to. I am working on offsets in front of and behind ROC and comparing with computerised models. Attempting to asses under or over correction. The learning curve is using the correct strokes to improve the shape. Found even 5 or 10 minutes can make a difference at this stage. Have to be very patient.
Reply With Quote
  #307  
Old 16-08-2017, 12:55 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Figuring Stage progress

Getting closer to a Parabolic 8" Mirror with the following comparison of the Ronchi calculator 85 grates per inch and a picture taken just using my iPhone. The first two compares inside ROC at -0.2 and the second two at Outside of ROC at 4.0. Pictures low quality
Click image for larger version

Name:	Inside ROC at -0.3.PNG
Views:	65
Size:	18.7 KB
ID:	217121

Click image for larger version

Name:	Inside-ROC-at--0.3.gif
Views:	69
Size:	133.6 KB
ID:	217122
I set my offsets on the Ronchi calculator at -0.3, -0.2, -0.1, 0.0, 0.1, 0.2, 0.3, 0.4, 0.5. The minus offsets return results from zones closer to the centre of the mirror and the positive numbers results from the outside zones of the mirror.
Attached Thumbnails
Click for full-size image (Outside ROC at 0.4.PNG)
17.9 KB107 views
Click for full-size image (Outside-0.4-ver-1.gif)
124.7 KB108 views
Reply With Quote
  #308  
Old 17-08-2017, 08:50 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Can anyone recommend a mirror coating service in NSW or Australia. Closest to Central Coast NSW would be convenient ?
Reply With Quote
  #309  
Old 17-08-2017, 10:02 PM
Saturnine (Jeff)
Registered User

Saturnine is offline
 
Join Date: Jul 2008
Location: Wollongong
Posts: 2,247
Hi Neil
I believe Wayne Sainty of Saintech in Taree does most of the mirror coatings for this area. There was / is a price list in the archives here somewhere along with ph.number and address . Several forum members have used his coating services . Someone else may jump in with a quick link to the post.
Reply With Quote
  #310  
Old 29-08-2017, 11:05 AM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Results of 133 grating on Ronchi. Testing using a pdf file.
Attached Files
File Type: pdf 133 Ronchi Grating results on 8 inch mirror pdf.pdf (400.1 KB, 112 views)
Reply With Quote
  #311  
Old 31-08-2017, 01:11 PM
nobby2's Avatar
nobby2 (Neil)
Registered User

nobby2 is offline
 
Join Date: Mar 2014
Location: Norah Head, Central Coast, NSW
Posts: 150
Before and After pictures. It was purchased as an old mirror with chips in the rear structure. Once coated (silver) should the rear (back of mirror) chips effect the final performance?
Attached Thumbnails
Click for full-size image (old-mirror-surface-to-be-ground-smooth.jpg)
56.1 KB132 views
Click for full-size image (Fiinal-polished-parabola.gif)
123.0 KB169 views
Reply With Quote
  #312  
Old 31-08-2017, 11:08 PM
Saturnine (Jeff)
Registered User

Saturnine is offline
 
Join Date: Jul 2008
Location: Wollongong
Posts: 2,247
hi Neil
Have been following your adventures as I have a few blanks sitting around that I would like to turn into mirrors when I get the time. As for chips on the rear edges, you wont even know they are there when the front surface is coated, they will have no effect on the image as you are only reflecting off the front surface. Suppose that goes without saying really.
Reply With Quote
  #313  
Old 28-10-2017, 04:15 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
mirror blanks

Gumtree https://www.gumtree.com.au/s-ad/mont...nks/1163433720

I tried to buy them but he won't post the blanks. Hopefully somebody in the Mont Albert VIC area will be able to use them.
Reply With Quote
  #314  
Old 30-10-2017, 07:54 AM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Quote:
Originally Posted by Baza View Post
Gumtree https://www.gumtree.com.au/s-ad/mont...nks/1163433720

I tried to buy them but he won't post the blanks. Hopefully somebody in the Mont Albert VIC area will be able to use them.
Hi, I have a few blanks of various sizes lying around, if you want. Only I'm in NZ, but willing to post if you want to buy. Send me a PM.

Stephen.
Reply With Quote
  #315  
Old 12-01-2018, 06:35 PM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
I have a 10" blank after being pointed to Andrews.
I've started grinding but seem to be stuck at 3.18mm, I am looking to go to about 6mm which should be around F3. Full size glass tile tool in use which has gone from 8 mm to about 5.5 mm thick. Just pushing across the blank with about 60% cover.
Any suggestion about getting to 6mm appreciated.
Barry
Reply With Quote
  #316  
Old 13-01-2018, 03:01 PM
OzEclipse's Avatar
OzEclipse (Joe Cali)
Registered User

OzEclipse is offline
 
Join Date: Jun 2012
Location: '34 South' Young Hilltops LGA, Australia
Posts: 1,324
Hi Barry,

I assume the depths you're quoting is where you are measuring the total depth of the curve, edge to edge of the blank?

If so, you are currently at f5 and need 5.2mm to get to f3. 6mm will give you f2.5.

Now that you have that curve, you can glue a full set of 8mm tiles to the first batch. You need long strokes to hog out the centre.

f3 is a deep soup bowl to parabolize on your first mirror.

Good luck

Joe
Reply With Quote
  #317  
Old 13-01-2018, 03:51 PM
dave brock's Avatar
dave brock
Registered User

dave brock is offline
 
Join Date: Dec 2011
Location: hamilton nz
Posts: 82
Quote:
Originally Posted by Baza View Post
I have a 10" blank after being pointed to Andrews.
I've started grinding but seem to be stuck at 3.18mm, I am looking to go to about 6mm which should be around F3. Full size glass tile tool in use which has gone from 8 mm to about 5.5 mm thick. Just pushing across the blank with about 60% cover.
Any suggestion about getting to 6mm appreciated.
Barry
If by pushing across the blank you mean tool on top then you should be mirror on top to deepen.

Dave
Reply With Quote
  #318  
Old 14-01-2018, 04:37 PM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
Thankyou
Reply With Quote
  #319  
Old 14-01-2018, 07:31 PM
OzEclipse's Avatar
OzEclipse (Joe Cali)
Registered User

OzEclipse is offline
 
Join Date: Jun 2012
Location: '34 South' Young Hilltops LGA, Australia
Posts: 1,324
Barry,

Are you measuring the depth of the curve on the mirror or by measuring the edge tile thickness on the tool? If the latter, this is not a reliable method.

If you are using the mirror curve depth across the whole disk, I have written you an excel spreadsheet to do the mirror curve depth to focal length calculation. You have to input the diameter of the mirror in mm and the curve depth in mm, it will calculate the rest for you.

Personally, I prefer the sun method. As long as it is a sunny day, tack a piece of white card on the end of a long dowel rod. Longer than the focal length.

Slosh water on the ground mirror surface, point it and the dowel at the sun and mark where the sun comes to focus. Measure the distance to the white card and that is the focal length. You can also put distance marks on the dowel to simplify measurements. It's simple and bulletproof.


Joe
Attached Files
File Type: zip mirror curve depth to focal length calculation.xlsx.zip (38.2 KB, 99 views)
Reply With Quote
  #320  
Old 16-01-2018, 09:41 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
No just commenting on how quickly the tool is being changed, it could be pyrex v ordinary glass.
Calculator indicates about f4.6 atm.
Barry
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 05:08 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement