Wanted: 12V Adapter for Canon 300D

[[1ponders]]

Wanted: 12V Adapter for Canon 300D or a link to where I can get one from.

[[1ponders]]

bump

[DeanoNZL]

Hi Paul,
Most of the 12v adapters I have seen are for charging the battery, not running the camera.
Found this link, if you are handy at electronics(or know someone who is)
Hope it helps.:)
http://www.danielmccauley.com/datasheets/datasheet_8vsupply01.pdf

[[1ponders]]

Thanks Adrian I'll have word to my local electronics guru and see what can be done.

[netwolf]

Paul, do you think this guru could make a few more?

Regards
Fahim

[[1ponders]]

:lol: I'll see what I can do, though I'm sure there are a few on the site here that could make a coupla extra bucks whipping up a few. ;) Maybe we should put the word out Fahim.

[iceman]

I'd pay someone here to make me a 12V adapter to run my 350D!

[netwolf]

Paul, yes I am sure and i would be happy to pay for it also.

What would be ideal is to make a dual kit AC and DC.

Regards
Fahim

[[1ponders]]

Get in line you two :lol:

Better put the call out. :lol:

[citivolus]

I have what you are looking for, from my G1 olden days. Basically it is a CA-PS400 "compact power adapter" plus DR-400 "DC Coupler". The output from the power adapter is 8.1V at 1.8A. I can't part with the CA-PS400, but to be honest I've never used the DR-400 component of it.

Here is another workable home built solution: http://home.arcor.de/panacocha/astro/index.html?atm_10d_power.html

Those in the know will know that I currently have two clone BP511 packs that could be had by anyone willing to pick them up (no mail Li-ion battery of questionable origin...). They could be used in the creation of one of these power supplies. I could probably strip out the battery component and mail the casing.

Eric

[[1ponders]]

I'd love to be able to understand what you said Eric, but as an electronics wiz I make a great landscaper. But thank goodness for google I see what you have. The DR-400 wouldn't fit a 300D would it?

[citivolus]

I suspect that it would fit a 300D. Look around the battery door for a small sliding tab that accommodates the power cable. If there is one, it should fit. Then it would just be a case of supplying it with around 8V DC. Several sites I just checked said that the DR-400 will fit the 300D.

I had a go at removing the casing from the old BP-511 clones, but they are on there fairly well. I will fully discharge those batteries and then have a better go. I got too distracted playing with my new green laser pointer in the smoke from the fires on North Stradbroke Island to try too hard tonight :)

Eric

[citivolus]

Oops, I just realized you were after a 12V source. That I don't have, but as posted above, a few minutes with a soldering iron and a DR-400 would provide you.

[[1ponders]]

Thanks Eric. If you are prepared to part with the DR-400 I'd be happy to come to some sort of arrangement. Pm me and we'll chat.

[citivolus]

Those circuits use a relatively expensive ($20US), no longer supported voltage regulator, which can be replaced with a 7808 costing $1.20 at Jaycar. This component is in a TO-220 case and is much smaller as well. I guess when people are ordering "free" samples, they don't pay much attention to the cost of the part in question. No wonder they couldn't find anyone selling those parts.

I might look into building some 11-35V to 8V power converters if there is enough interest. People would still need to supply their own BP-511 case or DR-400 on one end. Cost would likely be under $20 each, I'd have to do a more detailed parts breakdown and see what I could get for cases.

I'll do some more research and narrow down the price range. If I could get an idea for how many people were actually looking for a supply, that would help.

Eric

[citivolus]

Oh, the one circuit uses the LM350T which is around the same price as a 7808 regulator, but requires a small amount of supporting circuitry. You can drop a few caps and resistors using the 7808, reducing the size and cost of the design slightly.

Edit: I take it back, if you want reverse polarity protection via a diode on the input, the 7808 gets you very close to 12V minimum input, so if you really need that extra volt of input range, the LM350T is better.