baileys2611
19-02-2022, 09:40 PM
Hi, I would like to sell my QHY10 OSC if anyone is interested in purchasing please PM. Purchased in 2017, has seen light and works well, condition is like new. I have the original box, all cables, power supply, USB, dessicant tube, dessicant, and so on. Nothing missing.
Asking $1000 plus shipping (down from $1500).
I have pictures taken with this camera prior to processing through a GSO-RC10A guided on an AP1600GTO. It has been connected via t-thread the whole time, no clamps or scratches. When not in use, it has been in my 'observatory' (shed), has not been rained upon or below -10degrees C or above +50degrees C (the shed is ventilated and monitored).
Here are some technical specs for those that like RPG books with lots of stats:
CCD sensor ICX493AQA
CCD size 1.8inch (APS size)
Total pixel 3964*2712
Effective pixel 3900*2616
Pixel size 6.05um*6.05um
CCD readout Type 2 field (1*1 binning)
Progressive Scan (2*2, 4*4 binning)
Full Well Approx 45Ke-
Peak QE 60% for Green and 50% for Red and Blue wavelengths.
Anti Blooming Gate Yes,-100dB
Image Download Speed – 18 secs (1*1 binning) 9 secs (2*2 binning) 4secs (4*4 binning)
Preview speed 4 secs (1*1 binning) 2 secs (2*2 binning) 1 sec (4*4 binning)
Supports 1*1, 2*2 and 4*4 Binning
Readout speed 600kpixel/s, 3Mpixel/s
Readout Noise Typically 8-10e-
System Gain 0.7e-/ADU
Dynamic Range 74dB
CDS Yes
ADC 16bit
Cooling: Single stage TEC and fan
Maximum Delta T 40 – 43 degrees C below ambient
Set point cooling: Yes
Power consumption (INPUT=12V) Minimum (TEC OFF) 3.6 Watts, TEC=50% 13 Watts, Maximum (TEC=100%) 30 Watts
Input voltage DC12V to DC201 power adapter
Safe Range (11V-13.5V)
Telescope Interface M42/0.75 screw & 2inch T ring
Maximum Center adjustment + or – 0.5mm
Maximum Tilt adjustment -1 Degree
CCD sensor to front surface: 20mm (without adjustment ring), 23mm (with adjustment ring)
Weight: (Camera body only, without DC201 and cables) 390g (without adjustment ring), 425g (with adjustment ring)
Camera size: Diameter – 63mm, Length – 120mm
Opto isolated guide port.
Asking $1000 plus shipping (down from $1500).
I have pictures taken with this camera prior to processing through a GSO-RC10A guided on an AP1600GTO. It has been connected via t-thread the whole time, no clamps or scratches. When not in use, it has been in my 'observatory' (shed), has not been rained upon or below -10degrees C or above +50degrees C (the shed is ventilated and monitored).
Here are some technical specs for those that like RPG books with lots of stats:
CCD sensor ICX493AQA
CCD size 1.8inch (APS size)
Total pixel 3964*2712
Effective pixel 3900*2616
Pixel size 6.05um*6.05um
CCD readout Type 2 field (1*1 binning)
Progressive Scan (2*2, 4*4 binning)
Full Well Approx 45Ke-
Peak QE 60% for Green and 50% for Red and Blue wavelengths.
Anti Blooming Gate Yes,-100dB
Image Download Speed – 18 secs (1*1 binning) 9 secs (2*2 binning) 4secs (4*4 binning)
Preview speed 4 secs (1*1 binning) 2 secs (2*2 binning) 1 sec (4*4 binning)
Supports 1*1, 2*2 and 4*4 Binning
Readout speed 600kpixel/s, 3Mpixel/s
Readout Noise Typically 8-10e-
System Gain 0.7e-/ADU
Dynamic Range 74dB
CDS Yes
ADC 16bit
Cooling: Single stage TEC and fan
Maximum Delta T 40 – 43 degrees C below ambient
Set point cooling: Yes
Power consumption (INPUT=12V) Minimum (TEC OFF) 3.6 Watts, TEC=50% 13 Watts, Maximum (TEC=100%) 30 Watts
Input voltage DC12V to DC201 power adapter
Safe Range (11V-13.5V)
Telescope Interface M42/0.75 screw & 2inch T ring
Maximum Center adjustment + or – 0.5mm
Maximum Tilt adjustment -1 Degree
CCD sensor to front surface: 20mm (without adjustment ring), 23mm (with adjustment ring)
Weight: (Camera body only, without DC201 and cables) 390g (without adjustment ring), 425g (with adjustment ring)
Camera size: Diameter – 63mm, Length – 120mm
Opto isolated guide port.