#1  
Old 24-04-2015, 09:29 AM
peter_4059's Avatar
peter_4059 (Peter)
Big Scopes are Cool

peter_4059 is offline
 
Join Date: Jun 2007
Location: SE Tasmania
Posts: 4,532
CatsEye Collimation question

I'm looking for some input from people experienced with collimating Newtonians with Catseye Collimation equipment. I've been tweaking the collimation on my Meade LXD55 SN10 but can't seem to get the hotspots to stack properly in the Infinity XLP offset pupil view.

This all started because I wanted to replace the stock plastic focuser with a Moonlite. As I had to remove the corrector plate cell/secondary to install the new focuser, I went to a lot of trouble to collimate the focuser by carefully determining (measuring around the tube) the point opposite the centre point of the focuser and adjusting the collimation using the Teletube cross hairs. While the scope was in pieces I also respotted the primary mirror with a Catseye Hotspot. I also checked the secondary offset - checked measurements according to this:
http://www.mikeblaber.org/sn10collimation.htm

I've managed to take some photos this morning that show where I've got to:

View through Teletube XL: pictures 1-3
View through Blackcat: picture 4
View through Infinity XLP centre pupil: picture 5
View through Infinity XLP offset pupil: picture 6

To me it appears the secondary rotation is ok (all mirror clips visible in image 3 however I can't seem to get the centre and offset pupil images to stack properly. I'm also wondering about the silver reflection at the left hand edge of the secondary mirror in the Blackcat image 4.

Any advice greatly appreciated.

Peter
Attached Thumbnails
Click for full-size image (Teletube1.jpg)
191.9 KB46 views
Click for full-size image (Teletube2.jpg)
195.3 KB50 views
Click for full-size image (Teletube3.jpg)
188.8 KB44 views
Click for full-size image (Blackcat.jpg)
190.8 KB51 views
Click for full-size image (CentrePupil.jpg)
192.5 KB49 views
Click for full-size image (OffsetPupil.jpg)
187.0 KB52 views
Reply With Quote
  #2  
Old 24-04-2015, 09:38 AM
Peter.M's Avatar
Peter.M
Registered User

Peter.M is offline
 
Join Date: Sep 2011
Location: Adelaide
Posts: 947
The first thing I would make sure of is that the collimator is at the focal point of the telescope. If that is not the case it does not matter what you do, the hotspots will never look right in the central and offset pupils.
Reply With Quote
  #3  
Old 24-04-2015, 10:33 AM
peter_4059's Avatar
peter_4059 (Peter)
Big Scopes are Cool

peter_4059 is offline
 
Join Date: Jun 2007
Location: SE Tasmania
Posts: 4,532
Peter, how do you define the focal point in the context of the autocollimator vs eyepiece vs camera? Do I focus with an eyepiece then replace that with the autocollimator?
Reply With Quote
  #4  
Old 24-04-2015, 11:12 AM
peter_4059's Avatar
peter_4059 (Peter)
Big Scopes are Cool

peter_4059 is offline
 
Join Date: Jun 2007
Location: SE Tasmania
Posts: 4,532
Thanks for the advice Peter. That seemed to work a lot better and was much easier to see the four images.
Attached Thumbnails
Click for full-size image (Blackcat.jpg)
195.0 KB43 views
Click for full-size image (centre.jpg)
192.6 KB46 views
Click for full-size image (offset.jpg)
187.1 KB45 views
Reply With Quote
  #5  
Old 24-04-2015, 12:15 PM
Peter.M's Avatar
Peter.M
Registered User

Peter.M is offline
 
Join Date: Sep 2011
Location: Adelaide
Posts: 947
That's looking much better. It is something that is not well defined I'm their instructions, but needed to get everything lined up. The reason I knew is because the offset image in your first go the hotspots are different sizes. In your second images they are the same!
Reply With Quote
  #6  
Old 24-04-2015, 12:20 PM
peter_4059's Avatar
peter_4059 (Peter)
Big Scopes are Cool

peter_4059 is offline
 
Join Date: Jun 2007
Location: SE Tasmania
Posts: 4,532
Good tip - I don't recall it being mentioned in their instructions either.
Reply With Quote
  #7  
Old 25-04-2015, 12:38 PM
Jason D's Avatar
Jason D (Jason)
Registered User

Jason D is offline
 
Join Date: Aug 2009
Location: California USA
Posts: 117
Quote:
Originally Posted by Peter.M View Post
The first thing I would make sure of is that the collimator is at the focal point of the telescope. If that is not the case it does not matter what you do, the hotspots will never look right in the central and offset pupils.
Spot on...

Here is more technical details:

When the autocollimator mirror is at the focal plane, reflection 2 image is located on the primary mirror surface -- same level as reflection P. Therefore, both will have the same apparent size and there will be no parallax as you view them from both pupils.

When the autocollimator mirror starts to move below the focal plane, reflection 2 will start to rise above the mirror surface. Not only it will appear larger but parallax will be introduced. The opposite is true.

If you look at the last photo of the first post, you will see the following:
1- Reflection 2 is larger than reflection P
2- You will also see reflection 6 which can only be seen when the autocollimator mirror is below the focal plane.

One more observation. Center spot reflection will appear slightly larger when the Blackcat is below the focal plane.

How critical is it to get the autocollimator mirror precisely at the focal plane?
NOT THAT CRTITICAL. As long as reflection 2 size appears about the same size as reflection P then the location of the autocollimator is good. I found that as long the the autocollimator mirror is within 1% of the scope's focal length from the focal plane, both reflections will appear about the same size. So, for a scope with 1000mm focal length, the autocollimator mirror location is OK if it stays within 10mm from the focal plane.

To be fair to Catseye instructions, it does state at the top:

"*Equal-sized images as illustrated & best results are achieved with the focuser/autocollimator racked in/out appropriately to place the autocollimator mirror at or very near the focal plane."

Jason
Attached Thumbnails
Click for full-size image (refl_2_focal_animation.gif)
79.7 KB43 views
Click for full-size image (above_below_fp.JPG)
36.8 KB38 views
Click for full-size image (center_spot_size.gif)
172.7 KB41 views
Click for full-size image (below_focal_plane.png)
47.2 KB43 views
Reply With Quote
  #8  
Old 25-04-2015, 02:58 PM
peter_4059's Avatar
peter_4059 (Peter)
Big Scopes are Cool

peter_4059 is offline
 
Join Date: Jun 2007
Location: SE Tasmania
Posts: 4,532
Thanks for the explanation Jason. I had failed to recognise the significance of the camera backfocus but now it makes perfect sense.
Reply With Quote
  #9  
Old 25-04-2015, 03:44 PM
multiweb's Avatar
multiweb (Marc)
ze frogginator

multiweb is offline
 
Join Date: Oct 2007
Location: Sydney
Posts: 22,060
Incredible illustrations as usual, Jason. How do you work all this stuff out. Seems like second nature to you. I just get a brain freeze thinking about it.
Reply With Quote
  #10  
Old 26-04-2015, 12:00 AM
Jason D's Avatar
Jason D (Jason)
Registered User

Jason D is offline
 
Join Date: Aug 2009
Location: California USA
Posts: 117
Quote:
Originally Posted by multiweb View Post
Incredible illustrations as usual, Jason. How do you work all this stuff out. Seems like second nature to you. I just get a brain freeze thinking about it.
Thanks for the compliment, Marc
I enjoy putting these diagrams and gifs together to help others.

Jason
Reply With Quote
  #11  
Old 26-04-2015, 09:26 AM
multiweb's Avatar
multiweb (Marc)
ze frogginator

multiweb is offline
 
Join Date: Oct 2007
Location: Sydney
Posts: 22,060
Quote:
Originally Posted by Jason D View Post
Thanks for the compliment, Marc
I enjoy putting these diagrams and gifs together to help others.

Jason
Yeah, they're great. I always save them up. I think I've got every single one you've done on my HD.
Reply With Quote
  #12  
Old 28-04-2015, 05:57 PM
tlgerdes's Avatar
tlgerdes (Trevor)
Love the moonless nights!

tlgerdes is offline
 
Join Date: Mar 2009
Location: Sydney
Posts: 2,284
I went through the same issues 4 years ago. Took a few emails back and forth with them before I saw the light.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 05:31 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement