#41  
Old 10-02-2005, 04:26 PM
Exfso
Guest
 
Posts: n/a
It is basically my own design. Sits on top of 9 poles cemented into the ground, and about 1.5 metres above the ground. I built the frame, floor, sides etc on top of the supporting poles. (all permapine), Dimensions 2.5x2.3x1.8m. In hindsight, I would have made it longer, but room where I put it was the deciding factor. I made the roof frame separate, and around its base are 6 heavy duty castors that allow the roof to fit into the top channels one the two top sides.(shown). It was damn heavy to lift up on top the 3 odd metres. I then attached the laserlite roof panels. The tracks extends out to one side and each of the 2 tracks are supported by angle iron to the front of the observatory. This is probably the only weak link, I need to make heavier duty supports, as the roof probably weighs about 100kg.
This photo probably shows it a little better.
Attached Thumbnails
Click for full-size image (observatory1.jpg)
62.8 KB875 views

Last edited by Exfso; 10-02-2005 at 04:31 PM.
Reply With Quote
  #42  
Old 10-02-2005, 04:32 PM
Exfso
Guest
 
Posts: n/a
Tried to add another photo on same post, will do it here. As you can see it looks a tad flimsy, but in reality is very strong. However I will re-engineer the supporting angles very soon. The total weight of the roof is supported via 6 castors on the entire length of the tracks, and it cant be seen here, but the tracks whilst they are timber are re-inforced with aluminium angle the whole length with aluminium strap on the base of the channel for the castors to roll on.
Attached Thumbnails
Click for full-size image (obs6.jpg)
152.9 KB797 views

Last edited by Exfso; 10-02-2005 at 04:39 PM.
Reply With Quote
  #43  
Old 19-02-2005, 06:08 PM
mick pinner's Avatar
mick pinner
Astrolounge

mick pinner is offline
 
Join Date: Feb 2005
Location: monbulk-vic
Posts: 2,010
my set-up
Attached Thumbnails
Click for full-size image (scan[1].jpg)
57.9 KB697 views

Last edited by iceman; 20-02-2005 at 05:22 AM.
Reply With Quote
  #44  
Old 21-02-2005, 05:32 PM
mick pinner's Avatar
mick pinner
Astrolounge

mick pinner is offline
 
Join Date: Feb 2005
Location: monbulk-vic
Posts: 2,010
Paul,
I'm currently making a 3D weight system for the scope which will have full length travel and then vertical adjustment, I made the brackets for the guide scope which work quite well and compared to the price of an original Meade item I think it's time well spent.
I'm also making a stainless steel dew shield 1.6mm very thin and very strong professionally rolled and welded then painted in Meade blue (helps being a spraypainter to match the colour), will cost about $150 not bad compaired to Meades $460 out of Bintel.
Thats enough waffle just thought you might like to see a shot of the observatory so far, the pier is 220mm steel, the roof and top half of the walls slides East and West, should be complete about this time next week all going well
Hope it's clear over your head
Mick.
Attached Thumbnails
Click for full-size image (000_0232_1[1].jpg)
49.2 KB615 views

Last edited by iceman; 21-02-2005 at 06:47 PM.
Reply With Quote
  #45  
Old 22-02-2005, 04:46 PM
Vermin's Avatar
Vermin (Tom)
Cloud dodger

Vermin is offline
 
Join Date: Dec 2004
Location: Hobart
Posts: 584
Yay! I picked up my Telekit today.

Some assembly requred!
http://www.webclot.com/scope/images/DSCF0016.jpg
Reply With Quote
  #46  
Old 23-02-2005, 09:32 AM
iceman's Avatar
iceman (Mike)
Sir Post a Lot!

iceman is offline
 
Join Date: Sep 2004
Location: Gosford, NSW, Australia
Posts: 36,760
Here it is.
Attached Thumbnails
Click for full-size image (meade-90.jpg)
59.3 KB780 views
Reply With Quote
  #47  
Old 26-02-2005, 09:53 PM
acropolite's Avatar
acropolite (Phil)
Registered User

acropolite is offline
 
Join Date: Feb 2005
Location: Launceston Tasmania
Posts: 9,019
Just started to make a nuisance of myself in these forums and thought you might like a laugh. I don't have a real scope yet but dug out my old Bushnell, made up a mount for my camera tripod and voila I can see Jupiter with 4 of it's moons and Saturn with it's rings all at 25x mag. Who says you need to spend money to have fun. Attached is combined image of the Bushnell and a shot of the moon (it's a bit cloudy tonight) handheld through the bushnell.
Attached Thumbnails
Click for full-size image (moonscope.jpg)
21.9 KB674 views

Last edited by acropolite; 20-03-2005 at 01:33 PM.
Reply With Quote
  #48  
Old 27-02-2005, 06:41 PM
Starkler's Avatar
Starkler (Geoff)
4000 post club member

Starkler is offline
 
Join Date: Sep 2004
Location: Melbourne
Posts: 4,900
Heres my latest aquisition

Orion 80ED , William Optics 2 inch diagonal
Attached Thumbnails
Click for full-size image (ed80.jpg)
44.9 KB728 views
Reply With Quote
  #49  
Old 27-02-2005, 09:32 PM
coxellis's Avatar
coxellis
Member

coxellis is offline
 
Join Date: Feb 2005
Location: Newcastle-upon-Tyne, UK
Posts: 33
What's the mount Robby?

Have to get an up to date shot of my kit in daylight.

8" Newt and 80mm f6 ED refractor on a modded HEQ5, SX Hx916 cam and QC3K SC1.5 guider.

I've now got ADM tube rings for the small scope.

Andy

http://coxellis.homehost.org/kitpic1.jpg

Is this more acceptable? Sorry not used to dial up users...

Last edited by coxellis; 28-02-2005 at 01:05 AM.
Reply With Quote
  #50  
Old 27-02-2005, 10:37 PM
Argonavis's Avatar
Argonavis (William)
E pur si muove

Argonavis is offline
 
Join Date: Feb 2005
Location: Brisbane
Posts: 744
This little number takes but 5 minutes to set up - remove covers, install Telrad, use trolley to move into yard, place ocular in focuser - done.

only problem - no tracking!! (except by hand)
Attached Thumbnails
Click for full-size image (pa160354.jpg)
51.6 KB573 views

Last edited by rumples riot; 28-02-2005 at 12:21 AM.
Reply With Quote
  #51  
Old 28-02-2005, 07:02 PM
Astroman's Avatar
Astroman (Andrew Wall)
<><><><>

Astroman is offline
 
Join Date: Feb 2005
Location: Paralowie, South Australia
Posts: 4,367
Here is a pic of my setup (so far)

http://www.theastroweb.com/astronomy.../scopedome.jpg

Details:

8" F/7 Dobsonian, homemade mount.
2.3m Domed Observatory, bit close to shed, may have to move it later when the wife lets me. It's actually painter black inside and now has a shutter that works. Turning it is a chore might need help with this one.
Reply With Quote
  #52  
Old 01-03-2005, 01:01 PM
MiG's Avatar
MiG
Registered User

MiG is offline
 
Join Date: Feb 2005
Location: Bentleigh, Melbourne
Posts: 246
Here's my stuff. The two grey tubes are my homemade collimation devices. One is a crosshair sight tube and the other is a collimation-less laser collimator. It utilises a lens-less $4 laser pointer to provide a wide angle point source. I think it's pretty much a cheshire because it relies on the centering of the shadow of the centre dot.
Courtesy of this website: http://web.telia.com/~u41105032/yacht/yacht.htm

The scopes are:
10" GSO Dobsonian with rack and pinion focuser and no fan (good price).
60 mm Tasco refractor.

Edit: Grrr, don't preview after attaching file.
http://www.members.optusnet.com.au/m...astro_gear.jpg

Last edited by MiG; 01-03-2005 at 01:04 PM.
Reply With Quote
  #53  
Old 02-03-2005, 07:48 PM
Argonavis's Avatar
Argonavis (William)
E pur si muove

Argonavis is offline
 
Join Date: Feb 2005
Location: Brisbane
Posts: 744
I put this together for a few dollars more. It works well but is not very compact.
Attached Thumbnails
Click for full-size image (bino mount.jpg)
58.4 KB673 views
Reply With Quote
  #54  
Old 04-03-2005, 09:39 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
HOORAY,

My eldest daughter bought a digital camera and I raced over and borrowed it for the night!

HERE'S MY BEASTY
Attached Thumbnails
Click for full-size image (12 incher.jpg)
126.9 KB912 views
Reply With Quote
  #55  
Old 04-03-2005, 09:46 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
This is my Home-made Quickfinder
Attached Thumbnails
Click for full-size image (quikfinder1.jpg)
59.4 KB682 views
Reply With Quote
  #56  
Old 04-03-2005, 09:48 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
Another angle of the Quickfinder
Attached Thumbnails
Click for full-size image (in quikfinder.jpg)
38.4 KB632 views
Reply With Quote
  #57  
Old 04-03-2005, 09:52 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
And those funny looking round things at the bottom end of the scope are counterweights I made out of Speaker Magnets. I have turned one upside-down so you can see the thin rubber attached so they don't scratch the tube.
Attached Images
 
Reply With Quote
  #58  
Old 04-03-2005, 09:55 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
And finally,

the piece de resistance . . .

The famous 'Bird Cage Shower Cap!'
Attached Thumbnails
Click for full-size image (shower cap.jpg)
16.4 KB839 views
Reply With Quote
  #59  
Old 04-03-2005, 10:41 PM
ballaratdragons's Avatar
ballaratdragons (Ken)
The 'DRAGON MAN'

ballaratdragons is offline
 
Join Date: Jan 2005
Location: In the Dark at Snake Valley, Victoria
Posts: 14,412
Just remembered,

My EP collection so far.
Attached Thumbnails
Click for full-size image (ep\'s.jpg)
41.6 KB903 views
Reply With Quote
  #60  
Old 05-03-2005, 06:37 AM
bytor666
Cygnus X-1

bytor666 is offline
 
Join Date: Dec 2004
Posts: 366
Hey Ken....that scope looks wonderful !!!...must be nice standing outside with just a shirt on while i freeze me bloomin arse off out here in Canada !!!...hahahahaha ....nice counterweights no need for anything but magnets !!!.....very impressive indeed !!!..I would LOVE to know where I can get a hold of a crayford-style focuser like yours because the one that I have is stock and it can't take the weight of my naglers .
-----------------------------
Markus
12" GSO SCOPE
Attached Thumbnails
Click for full-size image (out.jpg)
50.0 KB1036 views

Last edited by bytor666; 05-03-2005 at 06:40 AM.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 08:41 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement