Go Back   IceInSpace > Beginners Start Here > Beginners Equipment Discussions

Reply
 
Thread Tools Rate Thread
  #1  
Old 12-12-2018, 01:34 PM
Jasp05 (Aaron)
Registered User

Jasp05 is offline
 
Join Date: Nov 2016
Location: Rockhampton
Posts: 226
HEQ5Pro Worm Gear Bearings - Part number or size?

Hi guys,

I recently stripped my mount down but haven't been able to get a hold of some new bearings for the worm drive mounts.

I never caught a part number or size for the bearings and have since put the mount back together.

Does anyone know the size or a part number I can use to order some Hybrid- Ceramic ones?

If all else fails I can strip the mount again to get sizing, but trying to avoid having to do that for now. (Ordering is going to take a few weeks over christmas I imagine and don't want my mount in parts around the house over the holidays.)
Reply With Quote
  #2  
Old 12-12-2018, 02:08 PM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
Aaron,
I found this:

In HEQ5 there are following bearings:

6x 6006 2RS - these are main RA and Dec shafts bearings
2x 30205 - tapered roller bearings
4x 689z (or 618/9) - these are small bearings for worm shafts
I used EZO bearings for worm and SKF/Timken for others.

As for plastic washers - these are used for precise placement of worm at worm wheel. There probably should be some washers already, because if you want to replace them, you need to use new one with the same thickness. I cut out proper dimension washers from teflon foil.

Hope that helps.
Reply With Quote
  #3  
Old 12-12-2018, 02:22 PM
Jasp05 (Aaron)
Registered User

Jasp05 is offline
 
Join Date: Nov 2016
Location: Rockhampton
Posts: 226
Thanks for that Ken,

I used FAG bearings for 6006-2RS and Timken for the Taper bearings also.

Just the bearing shop in town doesn't stock the smaller ones unfortunately.

Did you just use standard bearings for the small worm drive ones? or go for the hybrid ceramic like everyone recommends?


Also with regards to the plastic washers. My mount had red fibre washes on both axis, instead of one plastic/ teflon and one fibre washer as per the guide by astrobaby. I'm going to assume this isn't a problem as my mount performs pretty well. (After my previous tune up it was consistently doing sub 1" guiding for hours.
Reply With Quote
  #4  
Old 12-12-2018, 02:29 PM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
Aaron,
Not my data....I've had my HEQ5 for over twelve years and never had the need to strip and re-grease etc.
I honestly believe (based on being a mechanical engineer with 50 years experience) that ceramic bearings in this application are all marketing hype.

The slow rotation and light loads only needs a smooth capable bearing....
Reply With Quote
  #5  
Old 12-12-2018, 03:45 PM
Jasp05 (Aaron)
Registered User

Jasp05 is offline
 
Join Date: Nov 2016
Location: Rockhampton
Posts: 226
I kind of doubted the fact these Ceramic Bearings would make a noticeable difference.

At least my wallet will be happier. Hybrid Ceramic Bearings were going to run up around $60 a bearing


Thanks again Ken.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 03:00 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement