#1  
Old 06-03-2021, 07:35 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
First Light Disaster

After recycling a lot of gear I finally had enough cash to purchase a Skywatcher Esprit 120 to replace my Televue 85 as my main imaging scope. I have had it for around 3 weeks and Wednesday night was the first good night for taking some photos.

So off to the park.

1. Setup scope
2. Connect battery the wrong way (reverse polarity)
3. Bang
4. Go home as my mount (AZEQ6-GT) is fried

So until a new motherboard comes i will only be able to admire my new purchase. I have setup 1,000's of times and this was the first time I have made this mistake.

Oh well ......
Attached Thumbnails
Click for full-size image (FirstLight.jpg)
54.3 KB93 views
Reply With Quote
  #2  
Old 06-03-2021, 07:42 PM
Peter Ward's Avatar
Peter Ward
Galaxy hitchhiking guide

Peter Ward is offline
 
Join Date: Dec 2007
Location: The Shire
Posts: 8,090
Quote:
Originally Posted by Zuts View Post
After recycling a lot of gear I finally had enough cash to purchase a Skywatcher Esprit 120 to replace my Televue 85 as my main imaging scope. I have had it for around 3 weeks and Wednesday night was the first good night for taking some photos.

So off to the park.

1. Setup scope
2. Connect battery the wrong way (reverse polarity)
3. Bang
4. Go home as my mount (AZEQ6-GT) is fried

So until a new motherboard comes i will only be able to admire my new purchase. I have setup 1,000's of times and this was the first time I have made this mistake.

Oh well ......
You are not Robinson Crusoe...I've done the same myself but luckily
the electronics were polarity protected.

Oh dear!
Reply With Quote
  #3  
Old 06-03-2021, 08:25 PM
Constant's Avatar
Constant (David)
Registered User

Constant is offline
 
Join Date: Mar 2016
Location: The Shire
Posts: 119
Quote:
Originally Posted by Zuts View Post
After recycling a lot of gear I finally had enough cash to purchase a Skywatcher Esprit 120 to replace my Televue 85 as my main imaging scope. I have had it for around 3 weeks and Wednesday night was the first good night for taking some photos.

So off to the park.

1. Setup scope
2. Connect battery the wrong way (reverse polarity)
3. Bang
4. Go home as my mount (AZEQ6-GT) is fried

So until a new motherboard comes i will only be able to admire my new purchase. I have setup 1,000's of times and this was the first time I have made this mistake.

Oh well ......
The only upside.... Motherboards arent expensive and they're easily installed, I've practice in this craft.
Reply With Quote
  #4  
Old 06-03-2021, 08:39 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
Quote:
Originally Posted by Peter Ward View Post
You are not Robinson Crusoe...I've done the same myself but luckily
the electronics were polarity protected.

Oh dear!
Good idea, I might opt for some protection as well.
Reply With Quote
  #5  
Old 06-03-2021, 08:41 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
Quote:
Originally Posted by Constant View Post
The only upside.... Motherboards arent expensive and they're easily installed, I've practice in this craft.
Sadly telescope motherboards are not cheap. An AZEQ6 motherboard is over $400.
Reply With Quote
  #6  
Old 06-03-2021, 08:51 PM
Rerouter's Avatar
Rerouter (Ryan)
Registered User

Rerouter is offline
 
Join Date: Jan 2021
Location: Sydney
Posts: 117
and they still don't fit a cheap mosfet reverse polarity circuit on them....
Reply With Quote
  #7  
Old 06-03-2021, 09:29 PM
billdan's Avatar
billdan (Bill)
Registered User

billdan is offline
 
Join Date: Mar 2012
Location: Narangba, SE QLD
Posts: 1,551
You can use a simple power diode to protect against reverse polarity.

Just connect the diode in series, with the Anode to the battery +ve lead and the Cathode to Main Board +ve line.

If you reverse the polarity, NO current will flow through the diode.
Reply With Quote
  #8  
Old 06-03-2021, 09:37 PM
h0ughy's Avatar
h0ughy (David)
Moderator

h0ughy is offline
 
Join Date: Apr 2005
Location: NEWCASTLE NSW Australia
Posts: 33,156
Sorry to hear that you have issues like this, and you're in good company as I have done this to imaging gear
Reply With Quote
  #9  
Old 06-03-2021, 09:59 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
Quote:
Originally Posted by billdan View Post
You can use a simple power diode to protect against reverse polarity.

Just connect the diode in series, with the Anode to the battery +ve lead and the Cathode to Main Board +ve line.

If you reverse the polarity, NO current will flow through the diode.
Not sure i want to touch the mainboard. I think i will wire the female plug to the battery terminals.

Assuming that this will not drain the battery when it is not drawing power?
Reply With Quote
  #10  
Old 06-03-2021, 10:01 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
Quote:
Originally Posted by h0ughy View Post
Sorry to hear that you have issues like this, and you're in good company as I have done this to imaging gear
Luckily the ASIAIR pro survived, but i guess I should check my cameras and focuser as well as they were plugged into the ASIAIR, actually I will do it tomorrow, too scared to check now.
Reply With Quote
  #11  
Old 06-03-2021, 11:35 PM
byronpaul's Avatar
byronpaul (Paul)
Registered User

byronpaul is offline
 
Join Date: Aug 2007
Location: Greenvale, Victoria, Australia
Posts: 372
Fingers crossed it only the mount
Reply With Quote
  #12  
Old 07-03-2021, 12:24 AM
billdan's Avatar
billdan (Bill)
Registered User

billdan is offline
 
Join Date: Mar 2012
Location: Narangba, SE QLD
Posts: 1,551
Not sure i want to touch the mainboard.

Sorry, I did not mean to suggest touching the mainboard (void warranty).

Solder the diode onto the +ve lead on your cable that's going to the 12V plug.
Reply With Quote
  #13  
Old 07-03-2021, 01:36 AM
Hemi
Registered User

Hemi is offline
 
Join Date: Dec 2010
Location: Darwin
Posts: 608
Sorry to hear that Zuts.
I have an azeq6 as well and really don’t understand why there is no reverse polarity protection.
Hopefully everything else has survived.

Best of luck
Reply With Quote
  #14  
Old 07-03-2021, 12:42 PM
The_bluester's Avatar
The_bluester (Paul)
Registered User

The_bluester is offline
 
Join Date: Feb 2011
Location: Kilmore, Australia
Posts: 3,342
It has mystified me for a long time why they don't add reverse polarity protection to these things. With many setups using bulldog clip connections to a battery, every setup is an opportunity to let the smoke out. Particularly when a decent percentage of them will get set up in the dark!
Reply With Quote
  #15  
Old 07-03-2021, 05:38 PM
Zuts
Registered User

Zuts is offline
 
Join Date: Mar 2007
Location: sydney
Posts: 1,830
More damage

Quote:
Originally Posted by byronpaul View Post
Fingers crossed it only the mount
So I have discovered some more damage. The ASIAIR pro boots up and recognises any USB device plugged into it but the DC power outputs are blown.

I can connect the camera/guide cam/focuser to separate power supplies and the usb to the ASIAIR pro then the pro can still control the devices.

So either i get the ASIAIR pro power module fixed, which is probably very unlikely to be possible or I can do the following.

1. Buy a Pegasus mini power adaptor which has 4 power outputs and run the mount, asiair pro, camera and focuser from that. Does anyone know if the pegasus ($360) can handle an AZEQ6, ASI2600MC, EAF focuser and AISAIR pro? It is rated at 10 amps.

2. Connect the 3 way splitter shown in the attachment to the battery and plug everthing into that. I dont need the focuser and camera powered at the same time and the guide cam is powered off the ASIAIR usb port. So 3 connectors would be enough. This only cost $30 but is untidy compared to the pegasus unit and does not allow for dew controllers. Is this a viable solution or could I damage something?

Cheers
Paul
Attached Thumbnails
Click for full-size image (plug.jpg)
182.8 KB66 views
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 06:04 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement