#1  
Old 08-08-2020, 05:26 PM
Hisanori's Avatar
Hisanori (Hisanori)
Registered User

Hisanori is offline
 
Join Date: Jul 2015
Location: Sydney (Hornsby, NSW)
Posts: 106
Home-made SCT Cooler

I thought this my little project may be useful to share with others. If succesful, it will be very cost effective. Any suggestions, advices or comments are welcome!

During the last rainy weekend, I made my own SCT cooler for 12 inch Meade SCT. Initially I was looking around the market to buy but surprisingly expensive. It is a simple mechanism. I thought I should be able to build for my own.

Before starting my project I researched whether anyone ever built DIY scope coolers. There were few examples were published but any of them didn’t inspire me. I decided to draw my own conceptual design and came up with dimensions after finding available parts at shops.

I adopted a method to “suck out” air from inside the telescope. Most of commercial versions, like Lymax SCT Cooler, are “blow in” air to inside the telescope. I could not find any pros and cons on different methods. But I found it is easier to build this way because for the “blow in” design (1) I am not sure about a suitable design of the nozzle where the air blow out, (2) I am not sure about a type of dust filters which is effective but also not slowdown airflow too much. If I have a good answer to these, it is not too difficult to modify later anyway.

I went shopping to local Jaycar Electronics and Bunnings to buy all parts. Not many things you need. At Jaycar, I bought 12V DC fan 80mm diameter ($19.95), ABS sealed box 115x90x55mm ($15.95), Cigar lighter plug, and RCA plug / panel socket. At Bunnings I bought 40mm 1M PVC pressure pipe ($8.62), 20mm 1M PVC pressure pipe ($3.98) and 40mm PVC pressure valve socket ($4.30).

It was not too hard to build. It’s all plastic not too hard to make holes. However, you need an exact size of hole-saw for the tube intake air from inside the telescope (20mm PVC pipe with external diameter 27mm). This intake tube is connected to the cavity of the sealed box where the exhaust fan attached. This whole air-intake chamber has to be airtight. Not only make an exact size of the hole but also I used silicon glue to seal the connection of the tube and the box to make airtight.

Another attention was needed on connection where the large tube is secured to the box. The large tube effectively holds up a weight of the box and the fan. I used a 40mm valve socket and cut out screw sections, then installed 6 tapping screws to connect the socket onto the box. The 40mm tube simply went into the socket but applied a silicon glue to close any gaps between.

Most important but used very practical solution was the dust filter. I bought a soup stock filter bag from Asian grocery store. I decided wrap this in four layers around air intake holes drilled on the large tube (40mm) using a paint masking tape (a replacement is also easy).

An external dimension of the 40mm large tube is not exact fit to the 2 inch EP holder (PVC pipes are indicated with an internal diameter but not external diameter). A purchased pressure PVC pipe was very close but still needed to tape up a couple layers of cloth tape until have exact fit to the EP holder.

Outcome you could see the next post in pictures. The first defocused image was Antares after left my 12 inch for 2 hours in outside without cooling fan on 19th Juy. The second image was Antares after running the cooling fan for 1 hour on 1st August. The third image was taken on the same day after running the cooling fan for 2 hours (Antares went behind a building. This is Kaus Australis. That’s why the colour is different). I can see clear improvement.

I’m happy with this new handy instrument. Only moderate concerns are: (a) whether any air holes hiding around focuser or the primary mirror covers (around a focuser knob or a mirror lock). I taped up unknown hole found next to the focuser knob just in case. If the scope is inhaling any airs without passing through the filter, this will accelerate dust accumulations, (b) the 80mm DC fan might be too powerful and pumping up air faster than an assimilation speed of the internal optical tube and mirrors.

The main unit should be kept in a dust proof case. For this reason I made a 12V cable detachable to the unit because often the cable picking up dirt and dust from the ground.

Hisanori
Attached Thumbnails
Click for full-size image (IMG_20200725_131552-1jpg.jpg)
99.9 KB108 views
Click for full-size image (IMG_20200725_131630-1.jpg)
84.0 KB98 views
Click for full-size image (IMG_20200725_131748-1jpg.jpg)
101.8 KB99 views
Click for full-size image (IMG_20200808_163342-1.jpg)
72.2 KB123 views
Click for full-size image (IMG_20200725_163821-1.jpg)
129.8 KB95 views
Click for full-size image (IMG_20200725_170813-1.jpg)
49.0 KB119 views
Click for full-size image (IMG_20200725_181645-1.jpg)
66.4 KB127 views
Click for full-size image (IMG_20200727_204835-1.jpg)
116.1 KB115 views

Last edited by Hisanori; 09-08-2020 at 11:14 AM.
Reply With Quote
  #2  
Old 08-08-2020, 05:29 PM
Hisanori's Avatar
Hisanori (Hisanori)
Registered User

Hisanori is offline
 
Join Date: Jul 2015
Location: Sydney (Hornsby, NSW)
Posts: 106
Additional photos

Please see the additional photos.
Attached Thumbnails
Click for full-size image (IMG_20200726_153846-1.jpg)
49.4 KB99 views
Click for full-size image (IMG_20200728_220524-1.jpg)
83.0 KB123 views
Click for full-size image (FOTO_20200802_193230.jpg)
33.3 KB138 views
Click for full-size image (FOTO_20200802_193345.jpg)
131.6 KB131 views
Click for full-size image (FOTO_20200802_193449.jpg)
131.8 KB131 views
Click for full-size image (IMG_20200801_141101_2-1.jpg)
50.6 KB102 views
Click for full-size image (IMG_20200802_112259-1.jpg)
39.8 KB115 views
Click for full-size image (IMG_20200801_180823-1.jpg)
190.3 KB89 views

Last edited by Hisanori; 08-08-2020 at 06:59 PM.
Reply With Quote
  #3  
Old 08-08-2020, 06:50 PM
Tulloch's Avatar
Tulloch (Andrew)
Registered User

Tulloch is offline
 
Join Date: Sep 2019
Location: Melbourne
Posts: 488
Nice, thanks for the instructions
Reply With Quote
  #4  
Old 08-08-2020, 07:04 PM
MortonH's Avatar
MortonH
Deprived of starlight

MortonH is offline
 
Join Date: Nov 2006
Location: Sydney
Posts: 3,762
Nice job but the wisdom these days is insulation not cooling.
Reply With Quote
  #5  
Old 08-08-2020, 08:05 PM
John K's Avatar
John K
Registered User

John K is offline
 
Join Date: Sep 2005
Location: Melbourne
Posts: 1,468
That's awesome! and sure beats drilling holes and attaching peltiers to the actual back plate of the telescope.

Good one for all the planetary imagers on IIS to watch!

John K.
Reply With Quote
  #6  
Old 09-08-2020, 11:57 AM
Sunfish's Avatar
Sunfish (Ray)
Registered User

Sunfish is offline
 
Join Date: Mar 2018
Location: Wollongong
Posts: 1,909
Great idea and good design to draw in external air through a filter which most designs overlook. Polyester fibre insulation would also make a good filter and I wonder if some medium such as silica beads could also dry the air.
Reply With Quote
  #7  
Old 03-09-2020, 09:03 PM
Hisanori's Avatar
Hisanori (Hisanori)
Registered User

Hisanori is offline
 
Join Date: Jul 2015
Location: Sydney (Hornsby, NSW)
Posts: 106
Home Made SCT Cooler and Home Made Optical Tube Dehumidifier

Thanks for all your comment!

Inspired by Ray's comment, I prepared two bags of silica gel using the same soup stock bag used as the air filter. Then wrapped around the air filter using rubber bands. The opening of the silica gel bag was stapled closely. Once the silica gel absorbed moisture the whole bag can be dried in an oven (100 - 120 degrees) It works!

In addition, I made a dehumidifier to attach EP folder to keep inside OTA moisture free (while keep in storage). Jaycar sells a sealed ABS box with a clear rid (a changing colour of silica gel can be seen without opening the box).

All works very well at a fringe of cost. (Except I needed to invest a hole saw for the exact size of the PVC tube... thought around $25 ).
Attached Thumbnails
Click for full-size image (IMG_20200828_174500-1.jpg)
101.9 KB93 views
Click for full-size image (IMG_20200828_182446-1.jpg)
38.2 KB92 views
Click for full-size image (IMG_20200815_141902_compress32.jpg)
212.9 KB66 views
Click for full-size image (IMG_20200815_141753_compress43.jpg)
197.3 KB64 views
Click for full-size image (IMG_20200818_221640_compress4.jpg)
177.9 KB53 views
Click for full-size image (IMG_20200819_203404_1_compress97.jpg)
190.6 KB63 views
Click for full-size image (IMG_20200819_210228_compress68.jpg)
201.8 KB69 views
Click for full-size image (IMG_20200819_212122_compress75.jpg)
198.8 KB66 views

Last edited by Hisanori; 07-09-2020 at 06:02 PM. Reason: New work was done
Reply With Quote
  #8  
Old 07-09-2020, 08:57 AM
Don Pensack's Avatar
Don Pensack
Registered User

Don Pensack is offline
 
Join Date: Aug 2006
Location: Los Angeles
Posts: 501
Quote:
Originally Posted by MortonH View Post
Nice job but the wisdom these days is insulation not cooling.
Perhaps.
But with an SCT Cooler on my 8" SCT, I got perfect star images at the start of the night after 45 minutes with the SCT Cooler in the scope during twilight.
When I didn't use the cooler, it was 3-4 hours before I stopped seeing thermal issues in the scope.
The reason was because I stored my scope at home in a closet that was usually around 20°C, but my observing site was typically 10°C at sunset and 0°C about an hour and a half later and maybe -5 to -8°C by dawn. The scope was always WAY too warm compared with the air.
The SCT cooler got the interior of the tube down to the ambient temperature quickly. In the middle of the night, I'd take a break and put it back in for 15-20 minutes while I was eating or using someone else's scope.
It worked like a charm and gave excellent star images when seeing allowed.
Reply With Quote
  #9  
Old 07-09-2020, 09:15 AM
Sunfish's Avatar
Sunfish (Ray)
Registered User

Sunfish is offline
 
Join Date: Mar 2018
Location: Wollongong
Posts: 1,909
Well done. Great result that the air is clean and dry.
For $25 you can buy a pack of cheap hole saws of different kinds which are good enough for plastic. The more expensive bi metal type I use on aluminium and hardwood. Be careful , clamp it all down to timber and go slow, or use a pedestal drill.

Quote:
Originally Posted by Hisanori View Post
Thanks for all your comment!

Inspired by Ray's comment, I prepared two bags of silica gel using the same soup stock bag used as the air filter. Then wrapped around the air filter using rubber bands. The opening of the silica gel bag was stapled closely. Once the silica gel absorbed moisture the whole bag can be dried in an oven (100 - 120 degrees) It works!

In addition, I made a dehumidifier to attach EP folder to keep inside OTA moisture free (while keep in storage). Jaycar sells a sealed ABS box with a clear rid (a changing colour of silica gel can be seen without opening the box).

All works very well with a fringe of cost. (Except I needed to invest a hole saw for the exact size of the PVC tube... thought around $25 ).
Reply With Quote
  #10  
Old 07-09-2020, 10:24 AM
Stonius's Avatar
Stonius (Markus)
Registered User

Stonius is offline
 
Join Date: Mar 2015
Location: Melbourne
Posts: 1,495
If SCT's require battling with cooling issues because of closed tubes, I'm suprised they don't do truss SCT's in the same way they do RC's. Maybe there's something to do with the corrector plate picking up reflections from behind the scope?


Markus
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 01:25 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement