#1  
Old 18-11-2018, 09:46 PM
John K's Avatar
John K
Registered User

John K is offline
 
Join Date: Sep 2005
Location: Melbourne
Posts: 1,357
Collimation fine tuning advice

Hi guys,

I am "tinkering" with my 9.5" CDK type scope to try and get a better understanding on the long term collimation process for this type of scope. Having only owned a Newtonian, what a luxury!

I am only tweaking the secondary at this stage and have tried a version of CCD inspector but was unable to really get measurements from it to make worth while adjustments.

At this stage, I am using Firecapture and and putting an out of focus (inside focus) star to try and get the best looking image in the centre of the camera I have - 1600mm.

My idea as recommended by Stefan who completely rebuilt the scope and the way he likes to do it is to try and find the perfect centre of the imaging train and moving the star around the field until most of the image is totally concentric. This however I am finding hard to achieve and replicate! Another way I to shoot an open cluster like M41 with all of the images out of focus to see where the perfect centre is and then move the secondary accordingly.

I have read the DSI collimation process and the image I am attached I think shows a generally balanced image what slightly out of collimation is some of the corners.

Can someone make some suggestions on the best way to balance the attached image based on the standard 3 screw secondary (centre screw I am ignoring as it will alter the distance to the corrector). One question I have should 3 screws always be adjusted? e.g. if one is turned counter clockwise should the other two be turned the other way? Or can I balance the image by simply tweaking only 2 screws to adjust tilt in one direction?

The airy disk also does seem a bit unusual.

I am not using a Taka Collimator - checking the secondary mark that the scope with a Newtonian type laser is showing that the laser does not point directly at the centre of the secondary - does that make a difference in any way as many manufacturers say it does not??

Thanks in advance for any advice.

Clear skies.

John K.
Attached Thumbnails
Click for full-size image (Collimation Test Nov 18_2018.jpg)
97.4 KB41 views
Click for full-size image (Collimation Centre Enlarged Nov 18_2018.jpg)
110.7 KB35 views
Click for full-size image (Collimation Test Nov 18_2018_Airy Disk Centre.jpg)
182.8 KB27 views

Last edited by John K; 19-11-2018 at 08:33 AM.
Reply With Quote
  #2  
Old 18-11-2018, 10:05 PM
multiweb's Avatar
multiweb (Marc)
ze frogginator

multiweb is offline
 
Join Date: Oct 2007
Location: Hinchinbrook
Posts: 17,879
Your fov looks well balanced. As far as diffraction rings go I reckon you are too far either side of the focus to make a good reading. You need to get closer to focus to see only a couple of rings. Then you'll be able to see which way to go. I usually go out of focus as the image is less impacted by turbulence then push the star towards the opposite direction where the rings are compressed then recenter and so on. I use all screws but I try to balance as not to over tighten any.
Reply With Quote
  #3  
Old 18-11-2018, 10:41 PM
markas (Mark)
Registered User

markas is offline
 
Join Date: May 2012
Location: Melbourne Australia
Posts: 268
The process I use for my CDK is first to get the secondary reference marks (two concentric circles on my scope) exactly concentric with the centre of a Tak or cat's eye - easier with the Tak because it has magnification - using only the secondary adjusting screws. I also find that a Howie Glatter laser plus Tublug works well



When that has been achieved, the secondary is collimated.


Then using a defocused star field, I adjust the primary screws only to get the central stars showing exactly concentric donuts, with the extreme corner stars as concentric as possible, with any deviation from concentricity symmetrical about the centre of the fov. This is very critical.



When all that comes together the in-focus image should be optimised across the whole fov.


It is critically important for these designs that the mirror to mirror distance be right on specification. The sweet spot is very tight for the best performance to be attained.


Mark
Reply With Quote
  #4  
Old 24-12-2018, 08:56 AM
John K's Avatar
John K
Registered User

John K is offline
 
Join Date: Sep 2005
Location: Melbourne
Posts: 1,357
Thanks for the advice everyone.

After 5 weeks of rain here in Melbourne, had another go last night using M41 as the field.

The secondary appears well centered - checked it with a newtonian laser and the laser hits the secondary right in the middle of the donut marker.

https://www.flickr.com/photos/johnka...posted-public/

https://www.flickr.com/photos/johnka...posted-public/

What are people's thoughts in terms of the defocused star field attached?

If anything, I am thinking the centre of the field is slightly more above centre/right of the taken image - so would have to move the image slightly down and left, but other then that seems quite symmetrical to me. Any adjustments I am making I am doing using only the secondary at this stage and have not touched the primary at all.

Look forward to advice.

John K.
Attached Thumbnails
Click for full-size image (31490960657_a0a0f105de_o.jpg)
178.6 KB34 views
Click for full-size image (32558618998_e0bd1e4e17_o.jpg)
171.4 KB27 views
Reply With Quote
  #5  
Old 24-12-2018, 09:15 AM
Merlin66's Avatar
Merlin66 (Ken)
Spectroscopy Wizard

Merlin66 is offline
 
Join Date: Oct 2005
Location: St Leonards, Vic
Posts: 6,780
John,
Al's Collimating Aid is an ideal tool to verify the doughnut is central....
http://www.iceinspace.com.au/forum/s...t=62696&page=2
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 05:01 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Lunatico Astronomical
Advertisement
SkyWatcher Australia
Advertisement
NexDome Observatories
Advertisement
OzScopes Authorised Dealer
Advertisement
Celestron Australia
Advertisement
Meade Australia
Advertisement
Astronomy and Electronics Centre
Advertisement