ICEINSPACE
Most Read Articles
Moon Phase
CURRENT MOON Waning Gibbous
92.2%
The Sun Now
Time Zones
Sydney*
10:09 am
Perth
7:09 am
Auckland*
12:09 pm
New York
6:09 pm
Paris
12:09 am
GMT
11:09 pm




  #1  
Old 19-10-2017, 12:56 AM
luka's Avatar
luka
Unregistered User

luka is offline
 
Join Date: Apr 2007
Location: Perth, Australia
Posts: 1,040
PHD2 calibration and drift alignment

Hi,
A question regarding the PHD calibration and drift alignment. My usual setup is:
1. First do the calibration so PHD knows which way the camera is pointing.
2. Then do the drift alignment and change the mount's azimuth and altitude.
3. Start imaging...

My question is if the changes of azimuth and/or altitude invalidate the calibration? Or are these "inaccuracies" in calibration insignificant?

For example, placing the mount on the ground and doing the initial rough alignment with a compass will likely result in a polar alignment that is few degrees out. Should we then do:
1. calibration
2. drift alignment
3. calibration again
4. check the drift alignment again
5. and probably finish with another calibration before imaging?

Haven't really seen anyone talking about this, is it all insignificant?

Thanks for your thoughts
Luka
Reply With Quote
  #2  
Old 19-10-2017, 01:30 AM
billdan's Avatar
billdan (Bill)
Registered User

billdan is offline
 
Join Date: Mar 2012
Location: Narangba, SE QLD
Posts: 1,143
Hi Luka,

You do not need to re-calibrate after doing the drift alignment.

If your chosen target is a long way from the meridian (or DEC=0) then you should re-calibrate.

However if you're using the ASCOM driver for the mount it will report the change in DEC to PHD and a re-calibration is not necessary.

Also if you do a meridian flip you will need to reverse the DEC settings in the mount tab. The ASCOM driver should report which side of the pier the scope is and then its automatic. Or just do another re-calibrate for peace of mind, which is what I do.

To re-calibrate press the shift key on the keyboard while you click the guide button.

Cheers
Bill

Last edited by billdan; 19-10-2017 at 02:05 AM.
Reply With Quote
  #3  
Old 19-10-2017, 09:22 AM
phomer (Paul)
Registered User

phomer is offline
 
Join Date: Nov 2009
Location: Maribyrnong
Posts: 114
Luka,

There is no point doing two polar alignments, however, I always do a second calibration, as it only takes a minute to do.

As far as polar alignment is concerned, the nearer the pole you are imaging, the more accurate it needs to be.

Regards

Paul
Reply With Quote
  #4  
Old 19-10-2017, 09:26 AM
multiweb's Avatar
multiweb (Marc)
ze frogginator

multiweb is offline
 
Join Date: Oct 2007
Location: Hinchinbrook
Posts: 17,466
I always do a calibration run in the area I'm going to image the DSO. I also redo calibration when slewing to a new area of the sky (including meridian flip). Calibration takes a few minutes anyway. Tracking/balance issues can last for a whole night. Not worth the hassle.
Reply With Quote
Reply

Bookmarks

Tags
calibration, drift alignment, phd

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 09:09 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Advertisement
SkyWatcher 2018 Catalogue
Advertisement
FLI Cameras and Imaging Accessories
Advertisement
Lunatico Astronomical
Advertisement
Interest Free Finance
Advertisement
NexDome Observatories
Advertisement
OzScopes Authorised Dealer
Advertisement
Bintel
Advertisement
SkyWatcher WiFi Adaptor
Advertisement
Astronomy and Electronics Centre
Advertisement