Go Back   IceInSpace > Equipment > DIY Observatories

Reply
 
Thread Tools Rate Thread
  #1  
Old 27-09-2020, 11:50 AM
Gadget4x4 (Peter)
Registered User

Gadget4x4 is offline
 
Join Date: Jun 2020
Location: Perth, Australia
Posts: 12
Insulation for sliding shed roof

Hi - I'm considering building a small shed with a sliding roof as an observatory but have concerns about condensation on the roof. Would like to know what others have have done to help prevent droplets forming and falling on equipment such as insulation used or other means.
Cheers Peter
Reply With Quote
  #2  
Old 27-09-2020, 11:57 AM
glend (Glen)
Registered User

glend is offline
 
Join Date: Jun 2013
Location: Lake Macquarie
Posts: 7,033
I just used foil insulation from Bunnings. Cheap, held in place by wire strung across the roof members. Personally I avoid metal roofing as it is heavy and as you guessed condensate forming; I used corrugated polycarbonate roofing, Suntuff brand, guaranteed for something like 15 years, comes in colours and has some translucency which can be useful.

https://www.bunnings.com.au/suntuf-s...ofing_p1015729
Reply With Quote
  #3  
Old 27-09-2020, 12:29 PM
bojan's Avatar
bojan
amateur

bojan is offline
 
Join Date: Jul 2006
Location: Mt Waverley, VIC
Posts: 6,932
I also think polycarbonate is very much OK. However, because of Covid restrictions, I can't advise anything else... because I couldn't do anything since March, apart from sliding roof itself, see here.
Reply With Quote
  #4  
Old 27-09-2020, 04:02 PM
Anth10's Avatar
Anth10 (Anthony M)
When its late stay awake

Anth10 is offline
 
Join Date: Jan 2016
Location: Briar Hill
Posts: 783
I can personally vouch for using sarking/sisalation - I’ve had no dramas with condensation to date and is must really for waterproofing. I’m like you Bojan , haven’t had the chance to get to the hardware store to get some earth wool to pack out the rafters in the ROR as yet. I have plans to do this and close it off with some 3mm plyboard to keep it all secured. Although it is starting to gain a bit of weight but hey we don’t want that scorching summer sun to have a chance nor the water droplets now do we.
Good luck Peter- I’m sure it will work out for you.

Anth
Reply With Quote
  #5  
Old 27-09-2020, 04:35 PM
Gadget4x4 (Peter)
Registered User

Gadget4x4 is offline
 
Join Date: Jun 2020
Location: Perth, Australia
Posts: 12
Thanks for the suggestions - will look into both the foil and polycarbonate.
Nice work Bojan - I'm considering a gable roof shed for mine.
With the foil Glen - do you notice any condensation at all?
Cheers Peter
Reply With Quote
  #6  
Old 27-09-2020, 04:41 PM
Gadget4x4 (Peter)
Registered User

Gadget4x4 is offline
 
Join Date: Jun 2020
Location: Perth, Australia
Posts: 12
Earthwool - - I like the idea of a thin layer sandwiched between the tin and the foil - depending on how thin you can get the batts. thanks Anthony.
Reply With Quote
  #7  
Old 27-09-2020, 05:05 PM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
My ROR roof was reclaimed tin roof section from the converted shed.
For the past five years it has been unlined and any condensation has run down in inside surfaces, with some dripping on the equipment.
Earlier this year, I lined the roof with sarking stapled to the wooden joists, so an “air gap” to the tin.
I’m impressed!!
No more drips, I assume any moisture is contained between the roof and the sarking. Works for me and very simple to install.
Reply With Quote
  #8  
Old 27-09-2020, 05:11 PM
Wilso
Registered User

Wilso is offline
 
Join Date: Nov 2016
Location: Adelaide
Posts: 414
Any sort of air gap between the insulation and the iron will work to stop condensation forming underneath.
Foam is also a good insulation, light weight and easy to install.
Plenty of products out there when you start looking.
Reply With Quote
  #9  
Old 27-09-2020, 08:16 PM
glend (Glen)
Registered User

glend is offline
 
Join Date: Jun 2013
Location: Lake Macquarie
Posts: 7,033
Quote:
Originally Posted by Gadget4x4 View Post
Thanks for the suggestions - will look into both the foil and polycarbonate.
Nice work Bojan - I'm considering a gable roof shed for mine.
With the foil Glen - do you notice any condensation at all?
Cheers Peter
No condensation Peter, but my roof is polycarbonate (Sun Tuff), it does not sweat like metal. Also there is an air gap between the Polycarbonate and the foil. It does a good job of keeping the temperature inside down in summer. I also used the foil to build a shroud for my mount, it slips over the mount when not in use and is internally heated by a small bulb in winter to prevent pier condensation.
Reply With Quote
  #10  
Old 27-09-2020, 10:02 PM
Gadget4x4 (Peter)
Registered User

Gadget4x4 is offline
 
Join Date: Jun 2020
Location: Perth, Australia
Posts: 12
Thanks - good ideas and options to consider.
Just have to clear the area now for the shed.
At least I have time to weigh up what to do and use.
Cheers Peter
Reply With Quote
  #11  
Old 05-10-2020, 01:03 AM
LostInSp_ce's Avatar
LostInSp_ce
Unregistered User

LostInSp_ce is offline
 
Join Date: Mar 2017
Posts: 754
+1 for polycarbonate, or anything that's not metal and is lightweight. There's a polycarbonate product specifically for roofing application that has an air gap built into it. I won't post brand names here, but a quick google search and you'll find it. The other benefit to using light materials is the ease that the roof will roll off especially if it's has to be done manually. If it's motorised then weight becomes less of a factor but should still be of consideration. Just my two cents.
Reply With Quote
  #12  
Old 05-10-2020, 10:56 PM
Gadget4x4 (Peter)
Registered User

Gadget4x4 is offline
 
Join Date: Jun 2020
Location: Perth, Australia
Posts: 12
Found a couple of suppliers that do a polycarbonate roofing with an air gap - Thanks for the idea. Cheers Peter
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 07:21 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement