#1  
Old 18-04-2018, 05:48 PM
DiscoDuck's Avatar
DiscoDuck (Paul)
Raider Nation

DiscoDuck is offline
 
Join Date: Apr 2014
Location: Adelaide
Posts: 691
EQ6 RA guiding issues

I've been having trouble with RA guiding for my last few sessions. Massive spikes in RA as per the attached PHD2 log - up to about 4". Dec on the other hand is ok.

I thought it might be balance, but ensuring it was imbalanced correctly made little difference. Also tried balancing perfectly and going very imbalanced.

Some guiding was much worse than what you see there, with the spikes happening every couple of guide frames.

Guide star was a bit faint, but if that was an issue, surely it'd have effected dec too. But tried a brighter guide star and similar issues.

Is the RA meshing too tight and it's sticking? What else could cause this?

Comments and ideas/advice much appreciated.

Thanks,

Paul
Attached Thumbnails
Click for full-size image (Log.jpg)
145.7 KB56 views
Reply With Quote
  #2  
Old 18-04-2018, 06:27 PM
ChrisV's Avatar
ChrisV (Chris)
Registered User

ChrisV is offline
 
Join Date: Aug 2015
Location: Sydney
Posts: 1,737
I'm no expert but I've seen periodic spiking when I've used the backlash compensation.
Reply With Quote
  #3  
Old 18-04-2018, 07:54 PM
alpal's Avatar
alpal
Registered User

alpal is offline
 
Join Date: Jan 2012
Location: Melbourne
Posts: 3,602
Hi Paul,
would my experience help you?

here:

https://www.flickr.com/photos/24719437@N03/6001169049
Reply With Quote
  #4  
Old 19-04-2018, 06:52 AM
Russj (Russ)
Registered User

Russj is offline
 
Join Date: Aug 2017
Location: Albury
Posts: 52
G'day Paul, I have a NEQ6 which had graph similar to yours but was perhaps a little more spiky, although I could still image at 10 mins subs with round stars,...... go figure . I eventually got my rms down to .6 (on a good night) by the following.

1. I hypertuned the mount, (didnt replace any bearing).
2. fitted a Rowan belt kit
3. Run PEC in EQmod
4. Run Predictive pec in PHD2

My mount works well now, rms will still move over 1 on a poor seeing night which is to be expected.

I used to look at some of the almost perfect graphs on other forums and wondered how they do it on cheaper unmodified mounts in light polluted cities, something did not ring true to me, the reason I mention this is because I went down this road, spent a lot of unecessary time trying to get a near perfect graph, which I stil am unable to achieve, my graph still spikes a bit but I've got tight round stars, thats all that counts in the final washup.

These links may help, https://groups.google.com/forum/?fro...en-phd-guiding
http://www.astro-baby.com/EQ6%20rebu...own%20Home.htm

If I can help with any of the above let know

Hope this helps Russ

Last edited by Russj; 19-04-2018 at 07:14 AM.
Reply With Quote
  #5  
Old 19-04-2018, 07:04 AM
Imme (Jon)
Registered User

Imme is offline
 
Join Date: Aug 2017
Location: Kyneton
Posts: 840
Quote:
Originally Posted by Russj View Post
G'day Paul, I have a NEQ6 which had graph similar to yours but was perhaps a little more spiky, although I could still image at 10 mins subs with round stars,...... go figure . I eventually got my rms down to .6 (on a good night) by the following.

1. I hypertuned the mount, (didnt replace any bearing).
2. fitted a Rowan belt kit
3. Run PEC in EQmod
4. Run Predictive pec in PHD2

My mount works well now, rms will still move over 1 on a poor seeing night which is to be expected.

I used to look at some of the almost perfect graphs on other forums and wondered how they do it on cheap mounts in light polluted cities, something did not ring true to me in, the reason I mention this is because beginners (myself included) and others often look at these graphs and try to replicate the graphs on their mounts without much success.
As long as you have tight round stars thats all that counts in the final washup

If I can help with any of the above let know

Hope this helps Russ
Couldn't agree more with that last paragraph......there are probably 300,000 or more mounts out there in the world, the best 50 guide graphs get posted as 'this is how good my guiding is' and then we all try to compare ours to that.

As long as you stars are round then the guiding is perfect in my opinion!
Reply With Quote
  #6  
Old 19-04-2018, 08:30 AM
Atmos's Avatar
Atmos (Colin)
Ultimate Noob

Atmos is offline
 
Join Date: Aug 2011
Location: Melbourne
Posts: 6,980
Something else that might be worthwhile is stripping your mount down and giving it a regrease. For a time I had some guiding issues (random 2” spikes) that started appearing. After a regrease they went away. You just have to remember how tiny a particle needs to be for it to show up in the tracking
Reply With Quote
  #7  
Old 19-04-2018, 11:07 AM
DiscoDuck's Avatar
DiscoDuck (Paul)
Raider Nation

DiscoDuck is offline
 
Join Date: Apr 2014
Location: Adelaide
Posts: 691
Quote:
Originally Posted by ChrisV View Post
I'm no expert but I've seen periodic spiking when I've used the backlash compensation.
Thanks Chris. I think (may be wrong ) that backlash compensation only affects dec guiding. In any case, I've been using that for quite a while without issue and this problem only surfaced in the last couple of weeks.

Quote:
Originally Posted by alpal View Post
Hi Paul,
would my experience help you?

here:

https://www.flickr.com/photos/24719437@N03/6001169049
Thanks. I agree the bar is rubbish! Don't know why they couldn't do a better job. In my case, I don't think it was the cause of this particular problem as it was in a stable position and not moving. But definitely worth my looking at. Thanks again.

Quote:
Originally Posted by Russj View Post
G'day Paul, I have a NEQ6 which had graph similar to yours but was perhaps a little more spiky, although I could still image at 10 mins subs with round stars,...... go figure . I eventually got my rms down to .6 (on a good night) by the following.

1. I hypertuned the mount, (didnt replace any bearing).
2. fitted a Rowan belt kit
3. Run PEC in EQmod
4. Run Predictive pec in PHD2

My mount works well now, rms will still move over 1 on a poor seeing night which is to be expected.

I used to look at some of the almost perfect graphs on other forums and wondered how they do it on cheaper unmodified mounts in light polluted cities, something did not ring true to me, the reason I mention this is because I went down this road, spent a lot of unecessary time trying to get a near perfect graph, which I stil am unable to achieve, my graph still spikes a bit but I've got tight round stars, thats all that counts in the final washup.

These links may help, https://groups.google.com/forum/?fro...en-phd-guiding
http://www.astro-baby.com/EQ6%20rebu...own%20Home.htm

If I can help with any of the above let know

Hope this helps Russ
Thanks Russ. Much appreciated. I've already got a belt kit in there and had a re-grease at the same time. That was about 2 years ago, so it may be in need of a refresh/retune. I'll chase that up.

I've played with PEC before in EQMod. Never tried PHDs one. Can that work together with the EQMod one or do they interfere?

Re stars, yes, they were not as bad as the guide RMS would suggest, but the frustration is I've had much better up until now, i.e. RMS usually no worse than 0.5" RMS.

Thanks again for the advice. I'll look into the re-grease/re-tune etc. And again very much appreciated.

Quote:
Originally Posted by Imme View Post
Couldn't agree more with that last paragraph......there are probably 300,000 or more mounts out there in the world, the best 50 guide graphs get posted as 'this is how good my guiding is' and then we all try to compare ours to that.

As long as you stars are round then the guiding is perfect in my opinion!
Well, round and small is even better

Quote:
Originally Posted by Atmos View Post
Something else that might be worthwhile is stripping your mount down and giving it a regrease. For a time I had some guiding issues (random 2” spikes) that started appearing. After a regrease they went away. You just have to remember how tiny a particle needs to be for it to show up in the tracking
Thanks Colin. Sounds like it's time to pull out the lithium grease!
Reply With Quote
  #8  
Old 19-04-2018, 11:38 AM
Russj (Russ)
Registered User

Russj is offline
 
Join Date: Aug 2017
Location: Albury
Posts: 52
I've played with PEC before in EQMod. Never tried PHDs one. Can that work together with the EQMod one or do they interfere?

The software developers at PHD guiding forum stated that eqmod PEC takes care of the PE at the mount, leaving other errors for PHD PPEC to correct.
So yes you can use bothe at the same time.
Reply With Quote
  #9  
Old 19-04-2018, 11:58 AM
DiscoDuck's Avatar
DiscoDuck (Paul)
Raider Nation

DiscoDuck is offline
 
Join Date: Apr 2014
Location: Adelaide
Posts: 691
Great. Thank you.

Quote:
Originally Posted by Russj View Post
I've played with PEC before in EQMod. Never tried PHDs one. Can that work together with the EQMod one or do they interfere?

The software developers at PHD guiding forum stated that eqmod PEC takes care of the PE at the mount, leaving other errors for PHD PPEC to correct.
So yes you can use bothe at the same time.
Reply With Quote
  #10  
Old 19-04-2018, 12:31 PM
alpal's Avatar
alpal
Registered User

alpal is offline
 
Join Date: Jan 2012
Location: Melbourne
Posts: 3,602
Quote:
Originally Posted by DiscoDuck View Post

Thanks. I agree the bar is rubbish!
Don't know why they couldn't do a better job.
In my case, I don't think it was the cause of this particular problem as it was in a stable position and not moving.
But definitely worth my looking at. Thanks again.


Hi Paul,
I spent over 20 years working with closed loop control systems.
Wobbly parts just don't work.
Did you take the counter weights off & just move the bar up & down?
How much play was there?
I think the latest belt driven EQ6 has solved that problem.

May I also add that Roger Davis from Bintel had a look inside my EQ6 once &
he adjusted the DEC axis for the correct amount of play.
The EQ6 can come out of the factory with all sorts of problems
& many have to be checked out by experts such as Roger.
It only takes one bit of grit somewhere or a mal-adjustment &
the guide graph will go crazy.

There are experts around who can hyper-tune these mounts
with special bearings etc -
but I wouldn't bother unless the counterweight bar is upgraded first.

cheers
Allan
Reply With Quote
  #11  
Old 21-04-2018, 06:59 PM
DiscoDuck's Avatar
DiscoDuck (Paul)
Raider Nation

DiscoDuck is offline
 
Join Date: Apr 2014
Location: Adelaide
Posts: 691
Just a quick update for others who may encounter such a problem: I backed off the RA meshing a bit (as per AstroBaby's site) and the spikes seem to have gone. I think it was RA sticking, as before the adjustment I could hear a slight change in tone as it rotated when slowly slewing.

Of course, I have more backlash than a Trump tweet now! But biasing the balance to the east seems to help with that.

Thanks all for the advice.

Other things like counterweight bar I may leave as I'm waiting on a new mount arriving anyway in the next couple of months

Thanks again.

Paul
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 09:50 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement