#1  
Old 14-12-2018, 10:00 AM
sharkbite
Look up!

sharkbite is offline
 
Join Date: Jul 2013
Location: All around, Sometimes up, sometimes...
Posts: 323
LX90 Battery question

I have some time over xmas to tinker...

While my lx90 works just fine with a 12v Sealed lead acid battery,
the cabling offends my sensibilities so......

i have some 26650 Lipo batteries doing nothing that
just happen to fit in the stock battery housing on the mount.

The Lx90 has two battery compartments allowing for 4 C cells each,
nominally requiring a 6 Volt input...which will vary depending on battery condition..

2 Lipos each side will supply of them produce way too many volts and could potentially
damage the motors(?), so i'm planning to incoporate a 6v regulator on each of the 2
battery packs.

Does anybody know whether the mount expects a 'proper' 6+6=12v,
or if i should set it just a little bit higher?

I ask this, as even the old SLA sits at about 13 volts most of the time...
just not sure how voltage change affects performance on this mount...
Reply With Quote
  #2  
Old 14-12-2018, 01:02 PM
iborg's Avatar
iborg (Philip)
Registered User

iborg is offline
 
Join Date: Feb 2015
Location: Lynbrook, Australia
Posts: 611
Hi Sharkbite


I also have an LX90 and very much like your idea. When I search "26650 Lipo batteries" most of what comes up refers to Li ion batteries. Such as in the link below.


Are you confident that you have LiPo batteries? If so, do you have a link?



https://www.jaycar.com.au/26650-rech...ipple/p/SB2315


Philip
Reply With Quote
  #3  
Old 17-12-2018, 08:10 AM
sharkbite
Look up!

sharkbite is offline
 
Join Date: Jul 2013
Location: All around, Sometimes up, sometimes...
Posts: 323
Quote:
Originally Posted by iborg View Post
Hi Sharkbite


I also have an LX90 and very much like your idea. When I search "26650 Lipo batteries" most of what comes up refers to Li ion batteries. Such as in the link below.


Are you confident that you have LiPo batteries? If so, do you have a link?



https://www.jaycar.com.au/26650-rech...ipple/p/SB2315


Philip
Hi Philip - oops, you are correct, mostly Li ion at 3.7v (which is what i have, and why i need a regulator, as fully charged they can hit over 4v)

jaycar also sells the 3.2v Lipo 26650 - which may not need regulation?
(I dont know for sure, as i dont know the tolerance of the lx90 to over volt, nor what these things charge to.)

i think i'll start with an exact 12v and see how things go
Reply With Quote
  #4  
Old 17-12-2018, 01:37 PM
iborg's Avatar
iborg (Philip)
Registered User

iborg is offline
 
Join Date: Feb 2015
Location: Lynbrook, Australia
Posts: 611
Hi


Sealed lead acid batteries, fully charged are up to 13.8V, half of that is 6.9V.


With the LiPo 26650 batteries at 3.7V x 2 = 7.4, just add a diode, big enough to handle the current.


This one should be fine

https://www.jaycar.com.au/6a10-6a-1000v-diode/p/ZR1024


I think it drops 1V and can handle 6A.

On each side setup 2 batteries plus one diode ((2 x 3.7V) - 1) x 2 = 12.8V


No problem! I think!!


If you go with the LiFe batteries, don't even need the diode! but, it would provide protection to batteies inserted backwards.



LiPo 3.7V

https://www.jaycar.com.au/26650-rech...ipple/p/SB2315


LiFe 3.2V
https://www.jaycar.com.au/26650-life...-3-2v/p/SB2317


I hope his makes sense.


At these prices for the batteries, I will for leads to die before thinking of doing it.


Have fun


Philip
Reply With Quote
  #5  
Old 18-12-2018, 08:11 PM
AussieSky's Avatar
AussieSky (Greg)
Registered User

AussieSky is offline
 
Join Date: Apr 2008
Location: Sutherland Shire, Sydney
Posts: 89
Pretty sure the voltage drop across the diode will be about .6V, but that would still keep you in the safe range, ie: about 13.6V
Reply With Quote
  #6  
Old 19-12-2018, 07:21 AM
sharkbite
Look up!

sharkbite is offline
 
Join Date: Jul 2013
Location: All around, Sometimes up, sometimes...
Posts: 323
Thanks Guys...

making the 'leccy bits are no problem for me

My question was more around what the mount expects or can stand...

I dont know if it is designed for a wide range of voltages, as one
would expect if it was supposed to work off a battery.

A regulated supply is a bit different....if i set it too high it might blow
the circuits, if i set it too low the controller could register an undervolt situation, and either slow down, or annoy me all night with stupid alarms.

I'll try dead on 12v and report back here with any findings.

cheers, and thanks for your responses.
Reply With Quote
  #7  
Old 19-12-2018, 06:00 PM
iborg's Avatar
iborg (Philip)
Registered User

iborg is offline
 
Join Date: Feb 2015
Location: Lynbrook, Australia
Posts: 611
Hi



I misread the data sheet, maximum forward voltage (at 6A) is 1 amp.


I just measured one as 0.55V.


For a constant voltage supply, I would still set it 13V, just to be lucky!


Philip
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 01:12 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement