#1  
Old 31-12-2015, 07:05 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Autoguiding Woes

Hi All, IU need some help here. I can't seem to get autoguiding working at all. I have a skywatcher EQ5Pro GOTO mount and I'm trying to use an ZWO ASI120MC for guiding. What I've done is as follows:

1. Installed ASCOM 6 platform and ZWO ST4 drivers and PHD2.
2. I plug the ZWO by USB into a netbook and a 6P6C RJ12 from the ZWO to the SYNSCAN unit.
3. Using a compass I point the mount to where the SCP should be (~168 degrees SSE); altitude angle at 33 (Sydney)and start sidereal motion with the hand controller once I've located my target.
4 Using PhD, I click on the camera button and select the ZWO option and for the mount the ST4 option. I then start the image capturing and select a star. Subsequently, I click on the target button so it can supposedly calibrate.

The RE and DEC angles are never orthogonal because I don't think PHD is controlling the mount at all; is there a way to tell.
Reply With Quote
  #2  
Old 31-12-2015, 07:19 AM
Atmos's Avatar
Atmos (Colin)
Ultimate Noob

Atmos is offline
 
Join Date: Aug 2011
Location: Melbourne
Posts: 6,980
If you use the ASI ST4 Mount for guiding you do need to have the camera plugged directly into the "Autoguide" port on the HEQ5 via the cable (RJ-7?).
Reply With Quote
  #3  
Old 31-12-2015, 07:25 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Thanks. This probably didn't come through clearly. I do plug the cable directly from the ZWO camera into the autoguide port. I bought an RJ12 (6P6C) (telephone cable) as this seems to directly into the ZWO and skywatcher.
Reply With Quote
  #4  
Old 31-12-2015, 07:27 AM
Shiraz's Avatar
Shiraz (Ray)
Registered User

Shiraz is offline
 
Join Date: Apr 2010
Location: ardrossan south australia
Posts: 4,918
yep, if you use ST4 you need an ST4 cable (I think it can have crossed over wiring - worth googling for your camera and mount) to connect between the camera ST4 output and the mount ST4 input. You select "on camera" in phd and you don't need ASCOM. Do you get movement when calibrating?

Alternatively, you can pulse drive the mount using ASCOM, in which case you need to feed RS232 signals from a USB converter on your computer to the mount through the handset (in PC direct mode) or if the RS232 converter provides low voltage RS232, you can feed it directly into the mount via the handset socket. This is explained on the EQMOD site.
Reply With Quote
  #5  
Old 31-12-2015, 07:41 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Quote:
Originally Posted by Shiraz View Post
yep, if you use ST4 you need an ST4 cable (I think it has crossed over wiring) to connect between the camera ST4 output and the mount ST4 input. You select "on camera" in phd and you don't need ASCOM.

Alternatively, you can pulse drive the mount using ASCOM, in which case you need to feed RS232 signals from a USB converter on your computer to the mount through the handset (in PC direct mode) or if the RS232 converter provides low voltage RS232, you can feed it directly into the mount via the handset socket. This is explained on the EQMOD site.
Thanks Ray. I then assume that the RJ12 I have is not sending the signals from the ZWO to the correct pins on the SYNSCAN unit then. I think the ST4 option sounds the simplest but finding an ST4 cable may be hard if the connections cross over from end to end. still confused here.
Reply With Quote
  #6  
Old 31-12-2015, 07:45 AM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
The ST-4 cable is a RJ-12 6p6c straight through wiring.
See the Shoestring notes:
http://www.store.shoestringastronomy...ort_cables.pdf

When this is connected between the camera and the mount, PHD should be able to send control signals to the mount.

In PHD you can use the manual guide buttons to see if the mount is reacting to the input signal.

Do don't say what guide scope you have?
Reply With Quote
  #7  
Old 31-12-2015, 07:51 AM
Shiraz's Avatar
Shiraz (Ray)
Registered User

Shiraz is offline
 
Join Date: Apr 2010
Location: ardrossan south australia
Posts: 4,918
Quote:
Originally Posted by SuperG View Post
Thanks Ray. I then assume that the RJ12 I have is not sending the signals from the ZWO to the correct pins on the SYNSCAN unit then. I think the ST4 option sounds the simplest but finding an ST4 cable may be hard if the connections cross over from end to end. still confused here.
That was wrong advice. as Ken points out a straight RJ12 will do. The cables can be crossed, but phd automatically compensates when it calibrates.

do you get star motion when calibrating?
Reply With Quote
  #8  
Old 31-12-2015, 09:53 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Quote:
Originally Posted by Merlin66 View Post
The ST-4 cable is a RJ-12 6p6c straight through wiring.
See the Shoestring notes:
http://www.store.shoestringastronomy...ort_cables.pdf

When this is connected between the camera and the mount, PHD should be able to send control signals to the mount.

In PHD you can use the manual guide buttons to see if the mount is reacting to the input signal.

Do don't say what guide scope you have?
Thanks for the reply. I'll give the manual guide buttons a try later in the say. FYI, I'm using the ZWO 60280 guidescope with an F6 150mm Newt.

Ray Because I can't drift align properly (small viewing window) the star continues to drift in the up or down diagonal direction. Hard to tell.
Reply With Quote
  #9  
Old 31-12-2015, 10:11 AM
glend (Glen)
Registered User

glend is offline
 
Join Date: Jun 2013
Location: Lake Macquarie
Posts: 7,033
SuperG since my guide equipment is almost the same I will offer this advice. The ASI 120 and the Zwo guidescope work perfectly together. Forget ASCOM, you don't need it now. Personally I hate PHD as I could not get it to hold up a session with my ASI camera. The ASI cameras are high frame rate video and PHD would often hang. I switched to Metaguide and it worked first time and never drops out. Metaguide has an ASI selection in the drop down box in Setup. Try Metaguide, It's free.
The ASI cameras come with a ST4 cable, just plug it into the ASI120 and the guideport on your mount, it works fine as supplied. Don't make it more complicated than it is, it works fine. Make sure you have the latest ASI driver on your computer, download it from ASI if you don't have it.
Reply With Quote
  #10  
Old 31-12-2015, 02:21 PM
jamiep (Jamie)
Registered User

jamiep is offline
 
Join Date: Apr 2009
Location: Melbourne, Australia
Posts: 362
Quote:
Originally Posted by Shiraz View Post
That was wrong advice. as Ken points out a straight RJ12 will do. The cables can be crossed, but phd automatically compensates when it calibrates.

do you get star motion when calibrating?
I spent a night debugging this with a mate some time ago. Whilst the notes are correct - very few RJ12 phone cables are actually 6 wires connected straight through. they vary normally between 1 pair and 2 pairs, and only specialist cables will have the three pairs.

his result was guiding that would try to issue pulses and even worked in one direction....

a quick visual inspection of the terminated ends will confirm how many cables are in there....

if in doubt, confirm with the tech's where you purchased the cable.
Reply With Quote
  #11  
Old 01-01-2016, 07:34 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Quote:
Originally Posted by jamiep View Post
I spent a night debugging this with a mate some time ago. Whilst the notes are correct - very few RJ12 phone cables are actually 6 wires connected straight through. they vary normally between 1 pair and 2 pairs, and only specialist cables will have the three pairs.

his result was guiding that would try to issue pulses and even worked in one direction....

a quick visual inspection of the terminated ends will confirm how many cables are in there....

if in doubt, confirm with the tech's where you purchased the cable.
Hmm I'm still at a loss here. The RJ12 cable has 6 pins on both ends. The first one I used only had two. I still cannot get any movement with manual control. I'm using the ASI ST4 ASCOM driver. I assume this is correct.
Reply With Quote
  #12  
Old 01-01-2016, 07:40 AM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
I need to set up the ASI camera to confirm, but I'm pretty sure the connection from the camera to the mount using the ST-4 cable needs the mount to be connected through the "On camera" setting under PHD.
When you have a good connection the PHD manual controls should show some small movements of the FOV.
Reply With Quote
  #13  
Old 01-01-2016, 11:43 AM
Camknox (Cameron)
Registered User

Camknox is offline
 
Join Date: May 2012
Location: Kalgoorlie, WA
Posts: 57
I had a vaguely similar problem with my iEQ45 mount and my Orion guide camera. They just wouldn't talk using the RJ connection. I switched to RS232 and immediately started to be able to guide.
Reply With Quote
  #14  
Old 01-01-2016, 12:29 PM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Hi Merlin

I did try a few different combinations of settings will double check the (WDM and On-Camera combo). Might be dummy question but plugging the RJ12 directly into the autoguide port is the right way and not the RJ11 on the hand controller right?


Otherwise I might have to end up going through through USB-->RS-232-->Hand controller (I think that's the other route).
Reply With Quote
  #15  
Old 01-01-2016, 01:09 PM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
Yeah,
From the camera port to the autoguide port on the mount.
(The RJ11 port on the handcontroller is basically for upgrading the firmware)
Reply With Quote
  #16  
Old 01-01-2016, 01:28 PM
glend (Glen)
Registered User

glend is offline
 
Join Date: Jun 2013
Location: Lake Macquarie
Posts: 7,033
Quote:
Originally Posted by Merlin66 View Post
....
(The RJ11 port on the handcontroller is basically for upgrading the firmware)
It does other things as well. It can be used to control the mount, and the Astro Devices Nexus wifi box plugs into that port to give you wifi control of the mount via Sky Safari or other planetarium software. Not trying to confuse the OP here but others might read that as well Ken.
Reply With Quote
  #17  
Old 01-01-2016, 02:08 PM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
Glenn,
Yes I realise all that....
Just trying to apply the KISS principle to the OP issue of guide signals to the mount.
Reply With Quote
  #18  
Old 01-01-2016, 02:34 PM
astrodavid
Registered User

astrodavid is offline
 
Join Date: Oct 2013
Location: Cohuna, Victoria
Posts: 24
Quote:
Originally Posted by SuperG View Post
Hmm I'm still at a loss here. The RJ12 cable has 6 pins on both ends. The first one I used only had two. I still cannot get any movement with manual control. I'm using the ASI ST4 ASCOM driver. I assume this is correct.
Hi - 6 pins doesn't automatically confirm 6 wires - you should be able to confirm by looking at the rj12 crimp and seeing the six wires in the channels behind the pin connections.

You can also note the straight through or twisted status of the cable by the colours in the channels at each end - hope I'm making sense


Eg - http://www.store.shoestringastronomy...ort_cables.pdf
Reply With Quote
  #19  
Old 10-01-2016, 08:53 AM
SuperG
Registered User

SuperG is offline
 
Join Date: Oct 2014
Location: Sydney, NSW
Posts: 120
Hi Again

I now have a USB-->RS232 connector. Do I plug the cable that came with the mount into the autoguide slot or the hand controller slot. The manual is about as clear as mud on this.

thanks
Reply With Quote
  #20  
Old 10-01-2016, 10:21 AM
Merlin66's Avatar
Merlin66 (Ken)
Registered User

Merlin66 is offline
 
Join Date: Oct 2005
Location: Junortoun Vic
Posts: 8,904
Hmmmm
You seem to have moved away from the direct camera>guide port on mount using the ST-4 option....why?
The serial/ usb and the original upgrade cable will go to the handcontroller.
The only cable that goes to the guide port on the mount is the ST-4 guider cable.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 09:59 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement