Go Back   IceInSpace > Equipment > Equipment Discussions

Reply
 
Thread Tools Rate Thread
  #1  
Old 27-02-2012, 07:11 PM
ericc (Eric)
Registered User

ericc is offline
 
Join Date: Oct 2009
Location: Maitland
Posts: 87
GSO dob gravity collimation drift

Hi all-Just a quicky-- if anyone can help?
I have a new 12" GSO dob that showing a collimation drift(on altitude)
and is quite noticable using the Catseye teletube and Autocollimator.

After collimation(lets say at 60deg) you can watch the catseye triangle via the teletube, move untill zenith is reached and returning to 60deg, collimation moves back to perfect again.
Its not much--but its there all the same.



-I have fitted heavy primary springs.
-The mirror locking screws do not help.
-Mirror clips are just right?
-Spider vane is tight(with washers fitted underneath)
-Fitted sec bobs knobs(with milk jug washer mod)and are firm
-Focuser is tight

Am I missing something--or should I expect a little flexure in the 12"?
I have a 10" that is set up the same way --and its brilliant at holding collimation!



Any thoughts would be really appreciated people!
Cheers-Eric
Reply With Quote
  #2  
Old 27-02-2012, 08:47 PM
barx1963's Avatar
barx1963 (Malcolm)
Bright the hawk's flight

barx1963 is offline
 
Join Date: Nov 2008
Location: Mt Duneed Vic
Posts: 3,978
Eric
Got your PM. I always collimate at the start of the night with the scope at roughly 45deg, that way I figure I minimise any movement that may occur as it moves through its range.
Take the locking knobs and chuck 'em away, completely useless if you have strong springs. I have used Bobs Knobs springs and seem to work OK.

As I only use my scope for visual work, I have not found geting too pernicky over collimation does at lot of good, quite frankly I could spend a lot more time, effort and money getting it just so, and probably couldn't tell the difference in the image anyways!
My time is much better spent looking at DSOs, drooling over scopes, or posting bits of largely useless info on IIS!

While a 12" needs to be well collimated and needs checking every night,
spending more than 1-2 minutes per session is a waste of time IMHO.

Malcolm
Reply With Quote
  #3  
Old 27-02-2012, 10:38 PM
Shiraz's Avatar
Shiraz (Ray)
Registered User

Shiraz is offline
 
Join Date: Apr 2010
Location: ardrossan south australia
Posts: 4,918
Hi Eric. The secondary support on the GSO is just adequate with the fairly heavy secondary. FWIW, the plastic secondary holder on mine was flexing, so I made up a much stiffer one using plastic water pipe fittings and it helped a lot - there is still some collimation drift as other parts move, but not as much. regards Ray
Attached Thumbnails
Click for full-size image (tt2secondary.JPG)
26.4 KB6 views
Reply With Quote
  #4  
Old 28-02-2012, 04:18 AM
ericc (Eric)
Registered User

ericc is offline
 
Join Date: Oct 2009
Location: Maitland
Posts: 87
Thanks for the tips guys--
Yes Malcolm--I did ditch the lock screws(but used em for further diagnosis).
Ah ha--I will check out the sec holder (as I suspect the prob may not be on the primary end)?
But I now know that its normal for some drift to occur.
Will give me something to play with!
Cheers-Eric
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 07:58 AM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Bintel
Advertisement
Testar
Advertisement