Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rating: Thread Rating: 12 votes, 4.92 average.
  #321  
Old 18-01-2018, 10:33 AM
OzEclipse's Avatar
OzEclipse (Joe Cali)
Registered User

OzEclipse is offline
 
Join Date: Jun 2012
Location: Young Hilltops LGA, Australia
Posts: 1,177
Ok so your edge tiles are down to a bit more than half thickness. I would keep grinding for now. It gets tricky. You don't want to run out of glass near the end of the 80 grit because then if you have to retile, you will be grinding just to grind the resurfaced tool to match the mirror. You definitely don't want to run out of glass on the edge during the fine grind or you'll have to go back to coarse grind to resurface the tool. Just monitor the situation. If it looks like you won't make it, resurface the tool with fresh tiles when there is maybe 3mm left on the edge. Then you'll have an even 8mm all over to finish the job.

Joe
Reply With Quote
  #322  
Old 23-01-2018, 05:21 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
Thanks, might do a tool refurb. soon.
Reply With Quote
  #323  
Old 23-01-2018, 08:10 AM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Hi Barry, I assume your using #80 grit. I would most definitely suggest "re-tiling" at this point in your grind to ensure you "break in" the new tiles as getting them to conform to the mirror curvature would take too much time once finer grades are employed, in fact almost impossible at say #220 and beyond.

Stephen.
Reply With Quote
  #324  
Old 24-01-2018, 06:57 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
Thanks, ordered dental plaster to make a new one & I'll wait until it arrives. Will also build a bit of weight into the cast as I found the current one worked much better with an additional 3kg.
Reply With Quote
  #325  
Old 22-03-2018, 06:27 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
10 inch mirror

Progress is slow, most days I get about an hours work. Currently fine grinding and was amazed at how quickly the rough grind marks were removed from the centre of the mirror. The edge however is a different storey, it is obviously turned down to about 1.5mm in from the outer edge but is slowly coming out. Probably 8-10 hours more fine grinding which should clean up the edge.
Sagitta is at 5.5mm and seems stable, can't see any pits at 10x over the majority of the surface.
Guess it is time to make some test gear.

Pitting at edge.
Attached Thumbnails
Click for full-size image (20180322_144127[1].jpg)
105.2 KB65 views

Last edited by Baza; 22-03-2018 at 01:54 PM.
Reply With Quote
  #326  
Old 26-03-2018, 12:19 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Good things take time.

Stephen.
Reply With Quote
  #327  
Old 26-03-2018, 01:45 PM
Stefan Buda
Registered User

Stefan Buda is offline
 
Join Date: Jul 2013
Location: Melbourne, VIC
Posts: 823
Quote:
Originally Posted by Baza View Post
Progress is slow, most days I get about an hours work. Currently fine grinding and was amazed at how quickly the rough grind marks were removed from the centre of the mirror. The edge however is a different storey, it is obviously turned down to about 1.5mm in from the outer edge but is slowly coming out. Probably 8-10 hours more fine grinding which should clean up the edge.
Sagitta is at 5.5mm and seems stable, can't see any pits at 10x over the majority of the surface.
Guess it is time to make some test gear.

Pitting at edge.
To fix up the edge, it would be much quicker to just go back to coarse grit.
Reply With Quote
  #328  
Old 10-04-2018, 09:33 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
Sagitta

Still polishing & beginning to test but would like clarification.

I have measured the sagitta at 6.02mm which gives an F of 2.6 and ROC of 1298mm.
When the mirror is in the test stand the reflected light comes to a tiny circle at approx 1254mm giving a differential of 44mm. Yellow paper not sitting flat but was necessary to get an image.

My conclusion is that the reflected light measurement is correct and that my sagitta measurement is wrong.

Has anyone had experience with this?
Attached Thumbnails
Click for full-size image (20180410_100255[1].jpg)
64.3 KB57 views
Reply With Quote
  #329  
Old 17-04-2018, 06:13 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
The light distance measurement was correct. More polishing, ROC is 1290 mm, Ronchi is showing straight lines across the centre but a TDE. A bit over a month before I get back to polishing.
Reply With Quote
  #330  
Old 30-04-2018, 09:04 AM
Lognic04's Avatar
Lognic04 (Logan)
Registered User

Lognic04 is offline
 
Join Date: Mar 2016
Location: Melbourne, VIC
Posts: 889
I'm mirror making! i have a build thread here
Reply With Quote
  #331  
Old 06-05-2018, 10:38 AM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Quote:
Originally Posted by Lognic04 View Post
I'm mirror making! i have a build thread here
Hi, Watching with interest.

Stephen.
Reply With Quote
  #332  
Old 06-05-2018, 01:38 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Re-coated 25" mirror (ready for Winter sky &Planetary oppositions)

Coating had pretty much expired on my 25" mirror (silver coating approx 13 months old). So using my collection of "garden sprayers" etc and "spray silver chemicals", did the re-coat. Actual chemicals used cost less than US$20.

Surprisingly previous DIY coating lasted quite well. As a comparison have attached a couple of pics. First is of the 25" mirror freshly coated. Second pic of my 33" mirror and 12+ months old silver coat (rough [after a clean or two] but still usable [just]).

Stephen.
Attached Thumbnails
Click for full-size image (IMG_4514.JPG)
166.7 KB75 views
Click for full-size image (IMG_4516.JPG)
131.1 KB77 views
Reply With Quote
  #333  
Old 06-05-2018, 02:37 PM
DavidU's Avatar
DavidU (Dave)
Like to learn

DavidU is offline
 
Join Date: Jul 2007
Location: melbourne
Posts: 4,835
Steve, I would be interested in where to get the sivering spray.
cheers
Reply With Quote
  #334  
Old 07-05-2018, 01:56 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Hi Dave,

AngelGilding: see pics of what you need. Enough chemicals to do approximately 6-8 25" mirrors.

Stephen
Attached Thumbnails
Click for full-size image (IMG_4335.jpg)
85.4 KB63 views
Reply With Quote
  #335  
Old 12-05-2018, 08:15 PM
frankly1's Avatar
frankly1 (Frank)
Registered User

frankly1 is offline
 
Join Date: Oct 2010
Location: Weyba Downs, Qld.
Posts: 34
Quote:
Originally Posted by sopticals View Post
Hi Dave,

AngelGilding: see pics of what you need. Enough chemicals to do approximately 6-8 25" mirrors.

Stephen
Hi all, been a bit busy for a few years so I haven't recoated my 19" mirror for awhile. It will be the third Qld Astrofest with same silver coating. I will admit it is a little "dusty" now.
Reply With Quote
  #336  
Old 15-05-2018, 04:42 AM
pixelsaurus's Avatar
pixelsaurus (Mike)
Registered User

pixelsaurus is offline
 
Join Date: Mar 2006
Location: Te Kuiti,NZ
Posts: 166
What is the best way to strip the coating of an overcoated mirror?

Cheers.
Reply With Quote
  #337  
Old 30-05-2018, 02:14 PM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Quote:
Originally Posted by pixelsaurus View Post
What is the best way to strip the coating of an overcoated mirror?

Cheers.
Ferric Chloride will strip aluminium coat.

Stephen.
Reply With Quote
  #338  
Old 10-06-2018, 08:40 AM
sopticals's Avatar
sopticals (Stephen)
Registered User

sopticals is offline
 
Join Date: Jun 2010
Location: Oamaru, New Zealand.
Posts: 226
Couple more mirrors ready for polishing.

Couple more mirrors ready to polish.Will begin work on the 33"f4 first. Its the second 33 I have attempted. The first is "in service" but needs more work also. Its ok for low power work (115x-200x). Goes deeper than my 25" with over 70% more light gathering power.

Stephen.
Attached Thumbnails
Click for full-size image (IMG_4530.jpg)
90.6 KB67 views
Click for full-size image (IMG_4482.JPG)
186.4 KB72 views
Reply With Quote
  #339  
Old 10-06-2018, 11:00 AM
Baza (Barry)
Registered User

Baza is offline
 
Join Date: Mar 2014
Location: Heathcote NSW
Posts: 82
There inspiring and look great. Be worth a trip to NZ just to see them.
Reply With Quote
  #340  
Old 15-06-2018, 07:52 PM
pixelsaurus's Avatar
pixelsaurus (Mike)
Registered User

pixelsaurus is offline
 
Join Date: Mar 2006
Location: Te Kuiti,NZ
Posts: 166
Quote:
Originally Posted by sopticals View Post
Ferric Chloride will strip aluminium coat.

Stephen.
Cheers. Sorry for the delay. Will it also remove any overcoating as well?
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 08:42 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Advertisement
Testar
Advertisement
Bintel
Advertisement