Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rate Thread
  #101  
Old 05-11-2018, 03:04 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
(20") My yahooing was a little premature. I had a better look today with a ke tester and it turns out I have a central hill. No biggy, I'm not quite finished polishing so I'll try moving the tool in a smidgin to see if it will fix itself.

I bought a laser collimator yesterday to use later but good for testing the haze on the mirror. I would have said the mirror done but laser says no.

It's a bit ironic that I was following Gordon Waite's tutorial and I note he also had a central hill prior to parabolizing.
Reply With Quote
  #102  
Old 05-11-2018, 05:46 PM
Lognic04's Avatar
Lognic04 (Logan)
Registered User

Lognic04 is offline
 
Join Date: Mar 2016
Location: Melbourne, VIC
Posts: 824
I have actually been using a laser collimator too!
Reply With Quote
  #103  
Old 07-11-2018, 08:25 AM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
I need to upgrade my turntable. I no sooner get the lap warmed up and working properly when the motor gets too hot and I've got to quit the session. The session only lasts about 10 minutes when it really needs an hour or more. If you recall I've got 2 el cheapo drill presses joined together but they are not designed for continuous running, I need a 1/2 horsepower.

Even though I'm nearly finished polishing I've still got the secondary to polish.
Reply With Quote
  #104  
Old 11-11-2018, 04:22 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Picked up a motor at the markets this morning, now I need a pulley.

I've been working on the UTA, fashioning the 6 x 25mm ally tubes up to the upper cage. I didn't want to buy 6 x 3m tubes because of the expense, I opted for 3 tubes and cut them in half, which left me with a longer than usual upper cage. I think I said before I've got coarse adjustment on the mirror cell and the secondary has got fine adjustment on the outer edge of the spider, so the entire spider, secondary backing and secondary all move as one. Apparently the mirror spacing is quite critical so I want to try and get it right the first time. (Yes, pics!)
Reply With Quote
  #105  
Old 16-11-2018, 08:01 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
(20") New motor up and running, did a solid 1/2 hr polishing, then did a comprehensive test. Haze test is good, Ronchi test is good, KE slight raised hump in the centre and a little zoney. GW says to smooth it with a 12" lap, so that's what I shall do.
Reply With Quote
  #106  
Old 16-11-2018, 08:11 PM
Lognic04's Avatar
Lognic04 (Logan)
Registered User

Lognic04 is offline
 
Join Date: Mar 2016
Location: Melbourne, VIC
Posts: 824
Just curious, is GW's advice directly or some sort of forum?
Reply With Quote
  #107  
Old 17-11-2018, 03:49 AM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Gordon Waite has a whole bunch of tutorials on Utube. His company, Gordon Waite Research, manufactures a Renegade 20" Dobsonian, and he lives in New Jersey. He personally gave me advice about 12 yrs ago when I was making my 16".
Reply With Quote
  #108  
Old 03-12-2018, 03:58 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Had a bit of a rest from pushing glass and did a bit of work on the uta and made up the secondary holder. Its just a 8" circle of ply held flat by 3 lengths of 25 x 1mm aluminium spider. The spider is attached to 3 dovetail slides and there is a length of 3/16" threaded rod through the middle for fine adjustment.

In the meantime I started reading ATM book 1 for the 3rd time. You know how I said the mirror was done, well after reading ATM for a bit, maybe its not so done after all. So, I did 2 x 1 hour sessions at 10rpm and no weight and the surface improved no end. I may do another hour or two then tackle the slight hump in the middle.
Reply With Quote
  #109  
Old 08-12-2018, 04:49 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Did a bit of work on the central hill with a 4" tool. It's very time consuming when you polish for 5 minutes, then let the mirror cool down for 30 minutes, then test for a bit, then cold press for another 30 minutes, then the rellies come and want to know what I'm doing. At the end of the day the hill is diminishing, ready for a new 12" lap to try and smooth the surface.
Reply With Quote
  #110  
Old 12-12-2018, 04:37 PM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Dumb! Did the aforesaid 3 hours smoothing on the 20" without rotating the mirror on the turntable. Even when testing I would pick it up, place it on the test frame, plonk it back on the turntable and carry on never assuming for a minute I was doing a bad thing, until it was too late. Now I have polished in some astigmatism! The book blames the turntable. I'll have to strengthen it a bit and put in a 4th jockey wheel. Probably the 380mm x 40mm concrete tool didn't help. It's already 3 layers of 12mm marine ply so you would think it was ok.
Reply With Quote
  #111  
Old 10-02-2019, 10:48 AM
Lognic04's Avatar
Lognic04 (Logan)
Registered User

Lognic04 is offline
 
Join Date: Mar 2016
Location: Melbourne, VIC
Posts: 824
Any news?
Reply With Quote
  #112  
Old 11-02-2019, 07:21 AM
Billyboy78 (Bill)
Registered User

Billyboy78 is offline
 
Join Date: May 2018
Location: CRESTMEAD Brisbane
Posts: 90
Hi Logan.
Nah, but I do think about it occasionally though. Its been too hot and humid to play in my tin shed. But thanks for asking, I'll keep you informed on any progress.

Bill
Reply With Quote
  #113  
Old 11-02-2019, 08:07 AM
Lognic04's Avatar
Lognic04 (Logan)
Registered User

Lognic04 is offline
 
Join Date: Mar 2016
Location: Melbourne, VIC
Posts: 824
hope you brought the pitch lap inside!
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 03:36 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Advertisement
Interest Free Finance
Advertisement
SkyWatcher 2018 Catalogue
Advertisement
Bintel
Advertisement
Lunatico Astronomical
Advertisement
SkyWatcher WiFi Adaptor
Advertisement
NexDome Observatories
Advertisement
OzScopes Authorised Dealer
Advertisement
Astronomy and Electronics Centre
Advertisement