Go Back   IceInSpace > Beginners Start Here > Beginners Equipment Discussions

Reply
 
Thread Tools Rate Thread
  #41  
Old 11-11-2019, 10:41 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
After
Attached Thumbnails
Click for full-size image (A3E9D06E-637C-4B7E-BC19-62B31C5C311A.jpeg)
96.0 KB33 views
Reply With Quote
  #42  
Old 12-11-2019, 02:36 PM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
made some progress on my belt drive last night, got most of the prototype gears made. tested the grip and meshing with a length of gt2 belt I have spare. fits way better than I thought it would.! this printer is amazing.
ordered a pair of 130mm belts from Brisbane, paid handsomely for shipping so I can get em before the weekend.
will then be a case of sorting out an idler wheel to tension the whole setup.
Reply With Quote
  #43  
Old 14-11-2019, 04:26 PM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Ordered my belts on Tuesday afternoon and they arrived this morning.
Australia post would normally take a week from Brisbane so it was nice to have the express bag option albeit pricey.
They appear to seat in the gears really nice.
Tomorrow I’ll be off to the bearing shop to buy some tiny bearings to make an idler wheel to get the belt onto as many of the small primary gear teeth as possible.
Attached Thumbnails
Click for full-size image (1FA77C60-2DDD-4184-B744-6BA2C08D7DCC.jpg)
106.7 KB10 views
Reply With Quote
  #44  
Old 10-12-2019, 08:54 PM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
So I’ve hit a roadblock. I can make a 9 tooth gear but it just isn’t strong enough. Just keeps snapping. So I’ve ordered a pair of 9tooth gears from Rowan engineering in uk. About 18 pounds a piece. I’m on holidays as of Thursday so hopefully they get here before I go back to work in a month.
In light of this setback, I’ve constructed an Arduino based electric focuser. About 90 percent done. Just a bit of mounting and should be sweet.
Reply With Quote
  #45  
Old 17-12-2019, 10:39 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Only realised after ordering the 9 tooth pulleys that they are a t2.5 not a gt2 like I was going to use.
Got onto Minature bearings Australia again and they just happened to have 2 of what I needed in stock.
They turned up today and they fit the 2 new 44 tooth pulleys I made nicely.
Hopefully the 9 tooth gears will be here soon.
Attached Thumbnails
Click for full-size image (CC7009E8-A8E4-4EFD-9B15-39884D237B99.jpeg)
158.1 KB12 views
Reply With Quote
  #46  
Old 19-12-2019, 10:25 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Rowan pulleys turned up today. Time to reassemble and test.
Going to have to sort out a couple of tensioners though. I have a bunch of small bearings and some idlers I printed out before.
Attached Thumbnails
Click for full-size image (3ED7BE3E-D6CB-4636-8ECE-AEAEA7061129.jpeg)
139.6 KB10 views
Reply With Quote
  #47  
Old 20-12-2019, 10:30 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Aaaand itís finally back together on the ra axis. Printing final gear for the dec axis now. Covers donít quite fit back on but itís a matter of millimeters. Some refinement of gear thickness and maybe a wee shave with the die grinder to take a bit of meat out of the mount.
Helluva lot quieter now. Be interesting when I get it in action to see how it goes. Been constantly Smokey here for weeks now. Canít see any stars at night.
I printed a t2.5 version of the 9 tooth gear. Seems fairly strong compared to the gt2 gears Iíd previously printed. Canít snap it off with my fingers like the first version. Maybe I didnít need the Rowan gears after all. Oh well.
I have a couple of t2.5 gears for one axis if anyone would like to give em a try. Have to supply ya own t2.5 belt though.
Attached Thumbnails
Click for full-size image (243E1B4C-EE67-49AA-BF87-B1F63A8EB3E7.jpeg)
71.9 KB12 views
Reply With Quote
  #48  
Old 21-12-2019, 07:38 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Both axis done.
Attached Thumbnails
Click for full-size image (5326E319-528E-4E17-B8D1-0316FBB63D26.jpeg)
81.3 KB15 views
Reply With Quote
  #49  
Old 27-12-2019, 09:15 AM
Pepper (Steve)
Registered User

Pepper is offline
 
Join Date: Dec 2018
Location: Tamworth
Posts: 130
Christmas night we had the smoke blow away for the most part so I was able to test the belt drive out.
first thing is the noise. you really don't realise how loud the stock metal spur gears are..
the goto is 100% unaffected. if anything its even more accurate after a single 2 star alignment..
obviously the backlash has been seriously reduced. still some there but its a lot better. I notice when centering a star it is more spritely changing directions in dec.
all in all cost about 100 aussie bucks.
tonight is looking superb. the smoke has blown off to the southwest and looking at a nice clear night for the first time in a while
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 10:49 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Advertisement
Star Adventurer
Advertisement
Astromechanics
Advertisement
Testar
Advertisement
Bintel
Advertisement
Lunatico Astronomical
Advertisement
Celestron RASA
Advertisement
EQ8-R
Advertisement
Astronomy and Electronics Centre
Advertisement