Go Back   IceInSpace > Equipment > ATM and DIY Projects

Reply
 
Thread Tools Rate Thread
  #1  
Old 07-07-2019, 04:44 PM
RussellH
Registered User

RussellH is offline
 
Join Date: Oct 2005
Location: Sunny Queensland
Posts: 160
Building an EQDirect cable from ftdi break out board

So Iím wanting to build an EQDirect cable to run Stellarmate from a Raspberry Pi to a HEQ5.

Trying to source the 5v ftdi cable is either difficult (mostly 3.3v versions on ebay) or expensive $15-$50 for 5v version.

I found these arduino breakout boards for the IC version of the ftdi controller https://rover.ebay.com/rover/0/0/0?m...2F192627116019. I may even possibly have some at home already in some of my arduino mega kit gear.

Is there some reason these couldnít be used instead of the expensive cable versions.

Thanks. Russell.
Reply With Quote
  #2  
Old 07-07-2019, 09:39 PM
mswhin63's Avatar
mswhin63 (Malcolm)
Registered User

mswhin63 is offline
 
Join Date: May 2009
Location: Bertram, Western Australia
Posts: 3,327
Shouldn't be a problem, need to make sure you get the TTL version. Others will not work. I have made a few in my time, including a Bluetooth version. They can be cheap but need to beware of some tutorials. I noticed on the EQMOD page that the modules are powered without decoupling capacitors that could cause some issues.
Reply With Quote
  #3  
Old 08-07-2019, 05:48 AM
RussellH
Registered User

RussellH is offline
 
Join Date: Oct 2005
Location: Sunny Queensland
Posts: 160
Thanks for the info.

This is the specific unit I was thinking of.https://rover.ebay.com/rover/0/0/0?m...2F183565646696

I’m an electronics tinkerer, not an expert, so a bit unsure about the decoupler concerns. Wouldn’t a decoupler normally go between Vcc and Gnd? Vcc isn’t active on EQDirect cable, so what noise suppression is required? How exactly have you handled this?

Thanks. Russell.

Last edited by RussellH; 08-07-2019 at 08:47 AM.
Reply With Quote
  #4  
Old 09-07-2019, 01:30 AM
mswhin63's Avatar
mswhin63 (Malcolm)
Registered User

mswhin63 is offline
 
Join Date: May 2009
Location: Bertram, Western Australia
Posts: 3,327
Decoupling is to prevent potential instability in a linear regulator. Personally, all my project use Switching regulators that have higher efficiency, especially useful for battery-powered applications.

Decoupling capacitors are placed on both the input and output.

Ripple is another factor but is in most cases covered in the power supply or the battery.

The best thing is to look at the datasheet as a way of verifying the decoupling requirements.

I am moving to Adelaide next week, and so I will not be looking at posts shortly so get your questions in. I don't have the time at the moment to look at datasheets, only provide general information until I move.
Top it off I will be reviewing a Bluetooth Mesh development system for IoT and will be busy with that for a while.

Cheers


Quote:
Originally Posted by RussellH View Post
Thanks for the info.

This is the specific unit I was thinking of.https://rover.ebay.com/rover/0/0/0?m...2F183565646696

I’m an electronics tinkerer, not an expert, so a bit unsure about the decoupler concerns. Wouldn’t a decoupler normally go between Vcc and Gnd? Vcc isn’t active on EQDirect cable, so what noise suppression is required? How exactly have you handled this?

Thanks. Russell.
Reply With Quote
  #5  
Old 09-07-2019, 11:40 AM
RussellH
Registered User

RussellH is offline
 
Join Date: Oct 2005
Location: Sunny Queensland
Posts: 160
Alright, I'll just have to wing it for now. I see a couple people have even been running the 3.3v chips on short cables without problems, so I guess it depends on your tolerance for glitches and frying your circuitry. Will be a couple weeks before I can get into building anything anyway.

Russell.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time is now 08:47 PM.

Powered by vBulletin Version 3.8.7 | Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Advertisement
Celestron Australia
Advertisement
OzScopes Authorised Dealer
Advertisement
Lunatico Astronomical
Advertisement
NexDome Observatories
Advertisement
Meade Australia
Advertisement
Bintel
Advertisement
SkyWatcher Australia
Advertisement
Astronomy and Electronics Centre
Advertisement