View Single Post
Old 08-08-2020, 05:26 PM
Hisanori's Avatar
Hisanori (Hisanori)
Registered User

Hisanori is offline
Join Date: Jul 2015
Location: Sydney (Hornsby Heights, NSW 2077)
Posts: 86
Home-made SCT Cooler

I thought this my little project may be useful to share with others. If succesful, it will be very cost effective. Any suggestions, advices or comments are welcome!

During the last rainy weekend, I made my own SCT cooler for 12 inch Meade SCT. Initially I was looking around the market to buy but surprisingly expensive. It is a simple mechanism. I thought I should be able to build for my own.

Before starting my project I researched whether anyone ever built DIY scope coolers. There were few examples were published but any of them didn’t inspire me. I decided to draw my own conceptual design and came up with dimensions after finding available parts at shops.

I adopted a method to “suck out” air from inside the telescope. Most of commercial versions, like Lymax SCT Cooler, are “blow in” air to inside the telescope. I could not find any pros and cons on different methods. But I found it is easier to build this way because for the “blow in” design (1) I am not sure about a suitable design of the nozzle where the air blow out, (2) I am not sure about a type of dust filters which is effective but also not slowdown airflow too much. If I have a good answer to these, it is not too difficult to modify later anyway.

I went shopping to local Jaycar Electronics and Bunnings to buy all parts. Not many things you need. At Jaycar, I bought 12V DC fan 80mm diameter ($19.95), ABS sealed box 115x90x55mm ($15.95), Cigar lighter plug, and RCA plug / panel socket. At Bunnings I bought 40mm 1M PVC pressure pipe ($8.62), 20mm 1M PVC pressure pipe ($3.98) and 40mm PVC pressure valve socket ($4.30).

It was not too hard to build. It’s all plastic not too hard to make holes. However, you need an exact size of hole-saw for the tube intake air from inside the telescope (20mm PVC pipe with external diameter 27mm). This intake tube is connected to the cavity of the sealed box where the exhaust fan attached. This whole air-intake chamber has to be airtight. Not only make an exact size of the hole but also I used silicon glue to seal the connection of the tube and the box to make airtight.

Another attention was needed on connection where the large tube is secured to the box. The large tube effectively holds up a weight of the box and the fan. I used a 40mm valve socket and cut out screw sections, then installed 6 tapping screws to connect the socket onto the box. The 40mm tube simply went into the socket but applied a silicon glue to close any gaps between.

Most important but used very practical solution was the dust filter. I bought a soup stock filter bag from Asian grocery store. I decided wrap this in four layers around air intake holes drilled on the large tube (40mm) using a paint masking tape (a replacement is also easy).

An external dimension of the 40mm large tube is not exact fit to the 2 inch EP holder (PVC pipes are indicated with an internal diameter but not external diameter). A purchased pressure PVC pipe was very close but still needed to tape up a couple layers of cloth tape until have exact fit to the EP holder.

Outcome you could see the next post in pictures. The first defocused image was Antares after left my 12 inch for 2 hours in outside without cooling fan on 19th Juy. The second image was Antares after running the cooling fan for 1 hour on 1st August. The third image was taken on the same day after running the cooling fan for 2 hours (Antares went behind a building. This is Kaus Australis. That’s why the colour is different). I can see clear improvement.

I’m happy with this new handy instrument. Only moderate concerns are: (a) whether any air holes hiding around focuser or the primary mirror covers (around a focuser knob or a mirror lock). I taped up unknown hole found next to the focuser knob just in case. If the scope is inhaling any airs without passing through the filter, this will accelerate dust accumulations, (b) the 80mm DC fan might be too powerful and pumping up air faster than an assimilation speed of the internal optical tube and mirrors.

The main unit should be kept in a dust proof case. For this reason I made a 12V cable detachable to the unit because often the cable picking up dirt and dust from the ground.

Attached Thumbnails
Click for full-size image (IMG_20200725_131552-1jpg.jpg)
99.9 KB50 views
Click for full-size image (IMG_20200725_131630-1.jpg)
84.0 KB43 views
Click for full-size image (IMG_20200725_131748-1jpg.jpg)
101.8 KB40 views
Click for full-size image (IMG_20200808_163342-1.jpg)
72.2 KB53 views
Click for full-size image (IMG_20200725_163821-1.jpg)
129.8 KB44 views
Click for full-size image (IMG_20200725_170813-1.jpg)
49.0 KB49 views
Click for full-size image (IMG_20200725_181645-1.jpg)
66.4 KB52 views
Click for full-size image (IMG_20200727_204835-1.jpg)
116.1 KB57 views

Last edited by Hisanori; 09-08-2020 at 11:14 AM.
Reply With Quote